Ayman Ali Abd-Eltwab

Prof. Dr. Ayman Ali Abd-Eltwab

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 June 2024 in Babylonian Journal of Mechanical Engineering
Verified
Journal Article
Open access
PDF file
HEHammad T. Elmetwally
Hammad T. Elmetwally
HSHani N. SaadAllah
Hani N. SaadAllah
M.S. Abd-ElhadyM.S. Abd-Elhady
M.S. Abd-Elhady
RARagab K. Abdel-Magied
Ragab K. Abdel-Magied
AAAyman Ali Abd-Eltwab
Ayman Ali Abd-Eltwab
In most applications, joining aluminum to copper using friction stir welding (FSW) is a primary manufacturing process followed by secondary forming processes. The aim of this study is to investigate the effect of FSW process parameters (speed and feed rate) on the formability of Al-Cu joints. Aluminum and copper blanks were welded at three different rotational speeds, i.e., 910, 1280, and 1700 rpm, and three different feed rates, i.e., 16, 29, and 44 mm/min. The base metals used in this study were aluminum (Al-1050) and copper in two states, i.e., as received and annealed. The mechanical properties of the base metals and the produced compounds were evaluated by tensile and hardness tests. The aluminum-copper joints were drawn into flangeless U-shape and cup shape using FSW to examine the formability of the joints. The maximum tensile load, punch load, and forming index were obtained when Al was at 1700 rpm and 16 mm/min, i.e., h. The welding was performed with annealed copper at the highest rotational speed and lowest feed rate due to work hardening of the joint. However, the ductility was highest at 1280 rpm and 44 mm/min, i.e., at medium rotation and highest travel speed. It can be depicted that when the FSW Al-Cu joint is further used in the forming process, moderate rotation and high feed speed should be adopted for welding to avoid work hardening and improve the ductility of the joint.

12 August 2024 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
AAAyman Ali Abd-Eltwab
Ayman Ali Abd-Eltwab
KHKhaled Hamdy
Khaled Hamdy
AEAhmed Elsheikh
Ahmed Elsheikh
ESEssam K. Saied
Essam K. Saied
NGNouby M. Ghazaly
Nouby M. Ghazaly
AGA.A. Gomaa
A.A. Gomaa

1 September 2024 in Manufacturing Technology
Verified
Journal Article
Open access
PDF file
AAAyman Ali Abd-Eltwab
Ayman Ali Abd-Eltwab
WAWalid Elsyed Ayoub
Walid Elsyed Ayoub
MEMohamed N. El-Sheikh
Mohamed N. El-Sheikh
ESEssam Khalaf Saied
Essam Khalaf Saied
NGnobey ghazly
nobey ghazly
AGA. A. Gomaa
A. A. Gomaa
Gears and toothed parts are significant components in power transmission systems. These parts usually manufactured by traditional methods such as machining by milling or forming by rotary forging. In this study, the forming of solid gears or toothed parts using a forging process that combines rotary forging and ballizing technique. The specimens were placed inside the die with excessive volume to fill the toothed part in the die. The forming tool applies pressure to the specimen while rotating it together with the die by the lathe machine chuck, while the tool advances continuously in the direction of the die. This reduces height of the specimen and increases its diameter, causing metal flow to fill die cavity teeth and form the gear or toothed part required for production. Two sets of experiments were performed. In the first set, optimization for the appropriate volume of four different sizes of dies and four forming tools was conducted. While in the second set, the effects of forming process variables on the forming load and tooth filling percentage was studied. The results showed that the best tooth filling ratio happened with specimen size of 1.2 to 1.4 times the volume size of the desired tooth for filling. The results also revealed that the forming speed, die size, and forming tool diameter affect the filling ratio and forming load.

22 December 2023 in Manufacturing Technology
Verified
Journal Article
Open access
PDF file
AAAyman Ali Abd-Eltwab
Ayman Ali Abd-Eltwab
GHGamal I. Helal
Gamal I. Helal
MEMohamed N. El-Sheikh
Mohamed N. El-Sheikh
ESEssam Khalaf Saied
Essam Khalaf Saied
AAAhmed M. Atia
Ahmed M. Atia
Conventional spinning is one of the oldest processes used widely in manufacturing to obtain cup shape products. Conventional spinning is the technique that produces axisymmetric part or component over rotating mandrel with the help of rigid tool known as rollers. The shape of roller is a very important parameter for the success of the spinning process. The present research is aiming to use ball shaped rollers as forming tools in conventional spinning process experimentally. The experimental work was carried out on the center lathe machine as forming machine, the spinning tool or spinning rollers were installed on a dynamometer replaced the tool post while the mandrel was mounted on the lathe chuck. The spinning tool in this work consists of three rollers performing conventional spinning. The set of rollers is mounted on jaws of lathe chuck which working as a holder for the spinning tool parts. The experimental work was conducted in order to test the proposed tool and investigate the influence of the main conventional spinning parameters (mandrel rotational speed, axial feed and blank diameter or spinning ratio) on the process forming load and the product quality. The response of the product quality and required load to process parameters such as rotational speed (76,150, 230 and 305 rpm), axial feed (0.08, 0.15,0.3, and 0.6 mm/rev) also examined new rollers in different mandrel diameters 45, 60 and 80 mm. The experimental results showed that, the suggested tool acquired a spinning ratio of 2.17 which is about 35% greater than the announced conventional spinning ratio of 1.6 without any addition to the tool just using the suggested Ball shaped roller arrangement. The mandrel rotational speed, and axial feed rate are the most pronounced parameters, which have great effects on the forming loads during the spinning process.

1 May 2025 in JES. Journal of Engineering Sciences
Verified
Journal Article
Open access
PDF file
HEHammad T. Elmetwally
Hammad T. Elmetwally
EFEmad A. Fahmy
Emad A. Fahmy
EAEman S. M. Abd-Elhalim
Eman S. M. Abd-Elhalim
AAAhmed M.I. Abu-Oqail
Ahmed M.I. Abu-Oqail
MEMohamed N. El-Sheikh
Mohamed N. El-Sheikh
AAAyman Ali Abd-Eltwab
Ayman Ali Abd-Eltwab
External gear components are used in a variety of production and manufacturing areas, including motion, energy, and power transmission in many industrial applications. Examples include transportation equipment, aerospace equipment, and machine tools such as lathes and milling machines, all of which rely on gearboxes. As a result, these components are receiving increasing attention. This paper introduces an innovative multi-level rotary ballizing technique for manufacturing toothed tubular parts in one stroke. The process was examined both experimentally and numerically. The experimental study focused on key parameters, including die rotational speed (100, 200, 315, and 400 rpm), mandrel axial feed rate (0.13, 0.15, 0.18, and 0.21 mm/rev), and cross-feed values (4.5, 5.5, and 6.5 mm), achieved using three levels of ball. Additionally, initial tube thicknesses of 6, 7, and 8 mm were analyzed. The study investigated the influence of these parameters on forming load, filling ratio, and the hardness of the formed product. The results demonstrated that these factors significantly impact forming load, filling ratio, and overall product quality. A mathematical model was developed to predict forming loads numerically, and the calculated results showed a strong correlation with experimental findings. Moreover, the experimental results confirmed the effectiveness of the proposed multi-level ballizing technique in successfully forming toothed parts with greater thicknesses while significantly reducing forming loads compared to the single level ballizing method.

23 December 2025 in Manufacturing Technology
Verified
Journal Article
Open access
PDF file
AAAyman Ali Abd-Eltwab
Ayman Ali Abd-Eltwab
EFEmad A. Fahmy
Emad A. Fahmy
MEMohamed N. El-Sheikh
Mohamed N. El-Sheikh
AAAhmed M. I. Abu-Oqail
Ahmed M. I. Abu-Oqail
HEHammad T. Elmetwally
Hammad T. Elmetwally
EAEman S. M. Abd-Elhalim
Eman S. M. Abd-Elhalim
Longitudinal externally splined parts have garnered increasing attention due to their critical role in power transmission across various industrial applications. This study explores the use of the internally rotating balliz-ing technique for manufacturing these components. The process was analyzed both experimentally and numerically through a mathematical model. The experimental investigation focused on key process parameters, including die rotational speed (50, 63, 80, 100, 125, 160, 200, 250, and 315 rpm), axial feed rate (0.13, 0.15, 0.18, and 0.21 mm/rev), interference between the balls and the tubular sample (cross in-feed: 2.5, 3.5, 4.5 and 5.5 mm), and initial tube thickness (4, 5, 6 and 7 mm). The study assessed the influence of these variables on the forming load and the quality of the produced longitudinal externally splined sleeves. A numerical model was developed to predict forming loads, and the findings indicated that these parameters significantly affect both (forming load and filling ratio). The optimal values for these variables were identified, and the numerical results showed a strong correlation with experimental findings.