Loess, predominantly distributed in arid and semi-arid regions of central and western China, exhibits low shear strength and structural instability, rendering it prone to geological hazards such as landslides and collapses, which pose significant threats to local infrastructure and safety. This study evaluated the urease activity of soybean and sword bean at different temperatures to screen the optimal enzyme source for enzyme-induced carbonate precipitation (EICP). Methods including single EICP, EICP combined with nano-SiO₂, and EICP combined with both nano-SiO₂ and soil stabilizer (SS) were adopted to enhance the surface strength of loess. The results showed that the EICP technique significantly improved the surface strength of loess, especially with the addition of nano-SiO₂ and soil stabilizer. This study confirmed that using sword bean urease treated at −20 °C for 24 h in combination with 1.5% nano-SiO₂ was both cost-effective and efficient in reinforcement. The incorporation of 5% soil stabilizer further enhanced the surface strength, and the accuracy was further verified by combining the results of SEM and XRD. Future research will focus on optimizing the material ratio to maximize the improvement of surface strength, providing an economical and feasible solution for rapid loess solidification, and evaluating the long-term durability under cyclic wet and dry conditions.

To address the challenge of surrounding rock instability in deep-buried tunnels crossing fractured fault zones, this study focuses on the Xigu Tunnel of the Lanzhou–Hezuo Railway. A combination of laboratory triaxial tests, an optimized multi-source advanced geological prediction workflow, and a site-specific parameter-weakened Mohr–Coulomb numerical simulation is employed to systematically reveal the physical–mechanical properties, spatial distribution, and deformation response of fractured rock masses under excavation-induced disturbance. The triaxial test results show that the average peak strength of the surrounding rock reaches 149.04 MPa; however, significant variability is observed among samples, and the failure mode exhibits a typical brittle–shear composite feature. The measured cohesion and internal friction angle are 20.57 MPa and 49.91°, respectively, indicating high intrinsic strength of individual rock blocks. Nevertheless, due to the presence of densely developed joints and crushed structures, the overall mass is loose and highly sensitive to dynamic disturbances such as blasting and excavation, revealing a unique mechanical paradox of high-strength rock blocks with low overall rock mass stability in deep-buried fractured zones. Joint TSP (Tunnel Seismic Prediction Ahead) and ground-penetrating radar (GPR) prediction reveals decreased P-wave velocity, increased Poisson’s ratio, and intensive seismic reflection interfaces; a quantitative index system for identifying the boundaries of narrow deep-buried fractured zones is proposed based on these geophysical characteristics. Combined with geological face mapping, these results confirm the existence of a highly fractured zone approximately 130 m in width, characterized by well-developed joints, heterogeneous mechanical properties, and localized risks of blockfall and groundwater ingress. The developed numerical model, with parameters weakened based on triaxial test and geological prediction data, effectively reproduces the deformation law of the fractured zone, and the simulation results agree well with field monitoring data, with peak displacement concentrated at section DK4 + 595, thus accurately identifying the center of the fractured belt as a key engineering validation result of the integrated technical framework. During construction, based on the identified spatial characteristics of the fractured zone and the proposed targeted support insight, enhanced dynamic monitoring and targeted support measures at the fractured zone center are required to ensure structural safety and long-term stability of the tunnel. This study develops an integrated engineering-oriented technical framework for deep-buried tunnels crossing narrow fractured zones, and provides novel mechanical insights and quantitative identification indices for such complex geological engineering scenarios.

Surface erosion of loess slopes in arid and semi-arid regions of China remains a critical geotechnical issue, requiring green and low-carbon stabilization techniques. This study investigated the effectiveness of enzyme-induced carbonate precipitation (EICP) for the surface spraying reinforcement of Q3 loess collected from a high-fill engineering site at Yan’an University. Single-factor tests, response surface methodology (RSM), surface strength tests, CT-based three-dimensional pore reconstruction, and scanning electron microscopy (SEM) were conducted to evaluate the effects of cementation solution concentration and spraying dosage. The cementation solution was prepared by mixing analytical-grade urea and anhydrous calcium chloride at a 1:1 molar ratio, and the specimens were compacted to a dry density of 1.4 g/cm³. The results showed that surface strength first increased and then decreased with increasing cementation solution concentration and spraying dosage. Spraying dosage had a more pronounced influence than cementation solution concentration; excessive spraying above 9 L/m² reduced surface strength because of the high water sensitivity of loess. Five replicate tests at the central point were conducted to evaluate experimental error. The optimal parameters were 1.5 mol/L for cementation solution concentration and 9 L/m² for spraying dosage. CT and SEM results showed that CaCO₃ precipitation filled large pores and cemented soil particles, reducing total porosity from 6.7% to approximately 4.0%. These findings indicate that EICP improves loess surface strength mainly through pore filling and particle cementation, providing guidance for the ecological protection of loess slopes.

Using the shield project of the Cai Cang Section tunnel of the Guangzhou Metro Line 13 to solve the problem that shield construction is difficult to start in a narrow space and it is easy to disturb the surrounding buildings and pipelines, the corresponding shield tunneling parameters, construction and transportation plans, residual soil management plans, and grouting reinforcement plans are designed. These are tailored according to different working conditions. Meanwhile, the MIDAS GTS 2022 numerical simulation software is applied to simulate and analyze the impact of shield tunneling construction on soil deformation, and to compare the effects before and after reinforcement of the soil layer during shield tunneling. The results show the amount of disturbance of building pipelines along the tunnel are effectively controlled by designing the corresponding shield tunneling parameters for three working conditions: contact reinforcement zone, entering reinforcement zone, and exiting reinforcement zone. In narrow spaces, three kinds of construction transportation modes (namely, horizontal transportation in the tunnel, translation transportation in the cross passage, and vertical transportation) ensure the smooth transportation of pipe segments and the smooth discharge of shield dregs. After the reinforced area is constructed, secondary grouting with cement mortar effectively reduces the erosion concrete segments by underground water. By comparing the deformation of the tunnel soil layer before and after reinforcement, it is found that the maximum surface deformation of the soil layer is significantly reduced after reinforcement. Specifically, the maximum settlement and maximum uplift are 0.782 mm and 1.87 mm respectively, which represent a reduction of 1.548 mm in the maximum surface settlement, and 0.16 mm in the maximum uplift compared with the unreinforced soil layer. This indicates that setting up a soil reinforcement zone during the initial launching stage can effectively reduce soil deformation. The Cai Cang Section tunnel shield project successfully completed the shield construction in a narrow space, which can be a reference and guide for similar projects.

Finite element software ABAQUS was used to calculate the dynamic characteristics of Xi'an Xiao Yan pagoda by a three-dimensional entity model, and a variety of factors were simulated on its dynamic characteristics. Results show that it is feasible to calculate the structural dynamic characteristics by a finite element three-dimensional entity model. Through model comparison process, it was found that tilted wall is favorable to the seismic performance. And the elastic-plastic time-history analysis was carried out to simulate the tower under the big earthquake damage, and the corresponding reinforcement measures were discussed according to the simulation results.