The efficient recovery of methanol is essential for improving the overall performance and economic viability of integrated carbon dioxide utilization processes. This study presents the process simulation, separation performance and techno-economic assessment of a methanol recovery section within an integrated CO2/CH4 co-valorization process for dimethyl ether production using ChemCAD. A rigorous equilibrium-based distillation model was developed following preliminary shortcut column design to evaluate the recovery of methanol from the methanol-rich stream obtained after dimethyl ether separation. The separation train consisted of flash separation followed by rigorous staged distillation, with operating conditions selected to maximize methanol recovery while maintaining stable column operation. The developed model achieved a methanol recovery of 98.39%, producing 420.73 kg h⁻¹ of methanol in the distillate while effectively rejecting water to the bottoms stream. The selected operating conditions required a reboiler duty of 900.86 MJ h⁻¹ and a condenser duty of 1050.86 MJ h⁻¹, corresponding to a specific energy consumption of 4.64 MJ kg⁻¹ of recovered methanol. Techno-economic analysis estimated a total installed cost of US$312,818, with the distillation column accounting for the largest share of the capital investment. The annual utility cost was estimated at US$118,164, with steam representing more than 90% of the operating expenditure, identifying thermal energy consumption as the principal target for future process optimization. The results demonstrate that the proposed methanol recovery section provides an efficient and economically attractive purification strategy for integrated CO₂ utilization processes while providing a practical basis for future process intensification and industrial scale-up.
The catalytic utilization of carbon dioxide (CO2) and methane (CH4) provides a sustainable pathway for the simultaneous conversion of two greenhouse gases into value-added fuels and chemicals. This study presents a steady-state simulation of a dimethyl ether (DME) production process using an integrated three-reactor system developed in ChemCAD. The process comprises dry reforming of methane over a Ni/Al2O3 catalyst to generate synthesis gas, catalytic methanol synthesis over a Cu/ZnO/Al2O3 catalyst, and methanol dehydration over γ-Al2O3 to produce DME. Thermodynamic calculations were performed using the Non-Random Two-Liquid (NRTL) model coupled with the latent-heat enthalpy method, while reactor performance was represented using literature-based Arrhenius kinetic expressions. The downstream process incorporated staged heat recovery, flash separation, gas compression, chilled condensation, and a primary distillation column for crude DME recovery. Under the simulated operating conditions, the integrated process produced 237.05 kg h⁻¹ of crude DME, with the primary distillation column recovering up to 93% of the DME present in the condensed liquid stream, leaving only 0.03 kg h⁻¹ in the column bottoms. The combination of staged compression and low-temperature flash separation significantly enhanced DME recovery by promoting the condensation of condensable species while rejecting non-condensable gases. The proposed process demonstrates the technical feasibility of integrating reaction engineering and separation technologies for efficient DME production from CO2 and CH4 and establishes a robust process platform for future optimization and industrial-scale implementation.
Using iron and steel slags as feedstock for a mineral carbonation reaction using carbon dioxide gas is an excellent technique because they are easily accessible, contribute to land pollution, and have a reasonable quantity of lime and magnesia. The rate at which ironmaking blast furnace slag dissolves in an aqueous solution of ammonium acetate was investigated in relation to pH, stirring speed, solvent concentration, and temperature. A one-factor-at-a-time experiment was conducted, pH was monitored to the maximum value of 11, stirring speed ranged from 100 to 200 rpm, solvent concentration was adjusted from 0.01 to 1 M, whereas the reaction temperature was maintained between 25 and 80 °C. The dissolution kinetics of ironmaking slag were calculated by fitting experimental data to a model of a diminishing core. Using Atomic Absorption Spectroscopy, the leach liquor was characterized under various experimental conditions. The results of the trial revealed that this reaction is driven by a chemical reaction model equation. A semi-empirical model was also developed from the experimental data to better describe the dissolution kinetics.