Douglas Henrique Vieira

Mr. Douglas Henrique Vieira


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2021 in Materials Science in Semiconductor Processing
Verified
Journal Article
Closed access
DVDouglas Henrique Vieira
Douglas Henrique Vieira
MOMaíza da Silva Ozório
Maíza da Silva Ozório
GNGabriel Leonardo Nogueira
Gabriel Leonardo Nogueira
LFLucas Fugikawa-Santos
Lucas Fugikawa-Santos
NANeri Alves
Neri Alves

29 October 2021 in Semiconductor Science and Technology
Verified
Journal Article
Closed access
RMRogério Morais
Rogério Morais
DVDouglas Henrique Vieira
Douglas Henrique Vieira
CGCristina Gaspar
Cristina Gaspar
Luís PereiraLuís Pereira
Luís Pereira
Rodrigo MartinsRodrigo Martins
Rodrigo Martins
EAE Neri Alves
E Neri Alves
Paper electronics has emerged as an ecofriendly, light, low-cost, and recyclable material for the fabrication of flexible and printed transistors. In this study, we present fully printed organic electrochemical transistors using an active layer of PEDOT:PSS, carbon electrodes, cellulose-based electrolyte, and three different papers as substrates: bond, vegetal, and Lumi Silk, relating the electrical properties to the different morphologies of the paper surfaces. Each paper presents different regularity, diffusion capabilities, and roughness, with significant influence on the transistor performance. The more organized and smooth the surface, the better the electrical characteristics, the best of these being the Lumi Silk, with higher I on / I off ratio of 46, on-current of 8.3 × 10 −5 A, V on of 1.3 V, and power gain of 43.5 dB associated with ultra-low hysteresis of 0.1 V, high transconductance of −57.3 μ S, and suitablity for flexible electronics and sensors applications.

21 September 2020 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
DVDouglas Henrique Vieira
Douglas Henrique Vieira
NBNafiseh Badiei
Nafiseh Badiei
JEJonathan E. Evans
Jonathan E. Evans
NANeri Alves
Neri Alves
Jeff KettleJeff Kettle
Jeff Kettle
LLLijie Li
Lijie Li
β -Ga₂O₃ is one of the promising semiconductor materials that has been widely used in power electronics and ultraviolet (UV) detectors due to its wide bandgap and high sensitivity to UV light. Specifically, for the UV detection application, it has been reported that the photocurrent was in the scale of microamps (μA), which normally requires sophisticated signal processing units. In this work, a novel approach based upon coupling of two Schottky diodes is reported, leads to a substantial increase in photocurrent (~186 times) when benchmarked against a conventional planar UV photodiode. The detectivity and responsivity of the new device have also been significantly increased; the rectification ratio of this device was measured to be 1.7 x 10⁷ with ultralow dark current, when measured in the reverse bias. The results confirm that the approach of coupling two Schottky diodes has enormous potential for improving the optical performance of deep UV sensors.

21 January 2022 in Semiconductor Science and Technology
Verified
Journal Article
Closed access
RMRogério Morais
Rogério Morais
DVDouglas Henrique Vieira
Douglas Henrique Vieira
MKMaykel dos Santos Klem
Maykel dos Santos Klem
CGCristina Gaspar
Cristina Gaspar
Luís PereiraLuís Pereira
Luís Pereira
NANeri Alves
Neri Alves
Printed electronics is a reputable research area that aims at simple alternatives of manufacturing low-cost, eco-friendly, and biodegradable electronic devices. Among these devices, electrolyte-gated transistors (EGTs) stand out due to their simple manufacturing process and architecture. Here we report the study of printed EGTs with in-plane gate transistor (IPGT) architecture based on zinc oxide nanoparticles. The drain, source, and gate electrodes with two different W/L channel ratios were fabricated using a screen-printed carbon-based ink. We also produced a conventional top-gate transistor as a standard device, using the same structure of the IPGT described above with the addition of an indium tin oxide strip positioned over the electrolyte as the top-gate electrode. The IPGT with W/L = 5 presented a high mobility of 7.95 ± 0.55 cm2 V−1 s−1, while the W/L = 2.5 device exhibited a mobility of 3.03 ± 0.52 cm2 V−1 s−1. We found that the measured field-effect mobility of the device can be affected by the high contact resistance from the carbon electrodes. This effect could be observed when the device’s geometric parameters were changed. Furthermore, we also found that the IPGT with W/L = 5 exhibited higher values for mobility and transconductance than the top-gate transistor, showing that the IPGTs architecture is a good approach for cheap and printed transistors with performance comparable to standard top-gate EGTs.

26 June 2019 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
MOMaíza S. Ozório
Maíza S. Ozório
MNMayk R. Nascimento
Mayk R. Nascimento
DVDouglas Henrique Vieira
Douglas Henrique Vieira
GNGabriel L. Nogueira
Gabriel L. Nogueira
CMCibely Martin
Cibely Martin
NANeri Alves
Neri Alves

13 January 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
RMRogerio Miranda Morais
Rogerio Miranda Morais
DVDouglas Henrique Vieira
Douglas Henrique Vieira
MOMaíza S. Ozório
Maíza S. Ozório
Luís PereiraLuís Pereira
Luís Pereira
Rodrigo MartinsRodrigo Martins
Rodrigo Martins
NANeri Alves
Neri Alves
Solution-processed devices are in general compatible with flexible and conformable electronics. However, some promising materials needs to be processed at high temperatures, which limits the applications and the use of different substrates. Among these materials we can highlight zinc oxide (ZnO), a semiconductor that stands out for transistors applications and is, in general, obtained at temperatures around 300 °C-400 °C. Here, we reported the combination of annealing at 150 °C, ultraviolet (UV) treatment and blending of ZnO nanoparticles (ZnO-NPs) with zinc nitrate and urea as a strategy to fabricate an inkjet printed electrolyte-gated transistor (EGT) with reduced temperature and improved performance, including a significant mobility improvement to 0.21 cm 2 /V $\cdot$ s, operating below 2 V bias, which is around 460% higher than the mobility of the EGT fabricated purely with ZnO-NPs.