Tyler Grimm

Mr. Tyler Grimm

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 June 2017
Verified
Conference Paper
Closed access
PDF file
TGTyler Grimm
Tyler Grimm
IRIhab Ragai
Ihab Ragai
JRJohn T. Roth
John T. Roth
Electrically assisted incremental sheet forming (EAIF) is a novel addition to the incremental forming (IF) method. One variation of this approach applies direct electrical current during forming. Many improvements over tradition IF can be seen by utilizing this method, to include greater part accuracy, reduced forming force, and greater formability. In order to maximize the effects of electrically assisted incremental forming, all parameters of the method must be investigated, including the polarity of the current passing through the part and the path that the applied current takes. The effects of altering these two parameters is the primary investigation in this research. It was determined that, in order to optimize springback reduction and formability during electrically assisted single point incremental forming, the tool should be assigned the positive electrode and the center of the workpiece should be assigned the negative electrode. Additionally, the mechanism behind the spalling effect inherent to EAIF is discussed.

27 June 2016
Verified
Conference Paper
Closed access
PDF file
TNTrey Neveux
Trey Neveux
BRBrandt J. Ruszkiewicz
Brandt J. Ruszkiewicz
TGTyler Grimm
Tyler Grimm
JRJohn T. Roth
John T. Roth
IRIhab Ragai
Ihab Ragai
There has been a push in the automotive and aerospace industries towards die-less forming processing that are able to reduce both part cost and part energy. Incremental forming is a die-less forming process that fabricates parts using hemispherical tools following a tool path (similar to that found with conventional milling operations), that slowly deforms the sheet metal into the final desired configuration. Global springback for incremental forming, as defined herein, occurs after the part is unclamped from the retaining fixture. This form of springback is currently a significant impediment to the process since, when the part is released, the residual stresses created during the forming process result in significant part distortion and thereby, undesirable part geometries. To reduce this issue, this paper examines the effect on direct electric current on residual stress and springback elimination when applied post forming, which previous work has shown the potential to reduce this issue. This work is an extension of previous work resented at MSEC 2015. The previous work examined applying electric current to areas of high residual stress through the material’s thickness. This work examines the effect of applying electric current along the length and width of a part (path testing). This work concludes that running multiple paths increases springback reduction and the order in which the path testing is conducted has very little appreciable effect on the springback reduction during path testing.

Verified
Journal Article
Open access
PDF file
TGTyler Grimm
Tyler Grimm
LMLaine Mears
Laine Mears
Electrical resistivity was used in this test methodology to estimate the relative precipitate density in AA7075. Various electrical test parameters were explored to determine the difference between pulsed and DC-type currents. No difference between these test conditions could be distinguished. Furthermore, an electroplastic effect was not needed to explain these results and the effects are likely to be caused by purely joule heating.

21 June 2021
Verified
Conference Paper
Closed access
PDF file
ADAmit B. Deshpande
Amit B. Deshpande
TGTyler Grimm
Tyler Grimm
LMLaine Mears
Laine Mears
The use of multiple material in the structural components of a vehicle allows for significant weight reduction. Friction element welding (FEW) is a novel method that allows the joining of two or more dissimilar material sheets. A limitation of this process is the chip formation in high strength aluminum alloys, which is observed as the protrusion of thin aluminum segments from under the head of the fastener. Chipping can degrade the joint’s strength over time due to accelerated crevice corrosion. A novel method is proposed to eliminate chip formation using thermal assistance. A grading scheme is developed to quantify the severity of chip formation. The effect of thermal assistance on chipping is analyzed. An investigation is also carried out to validate that the thermal assistance does not negatively affect the process time, energy, and joint strength. Thermal assistance is proposed to be a novel method of overcoming this limitation to allow more widespread use of the FEW process for higher-strength aluminum alloys. Future work will include the development of feasible, rapid methods of heating and measurement of energy utilization for implementation in the industrial environment.

21 October 2023 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
NKNilesh Ashok Kharat
Nilesh Ashok Kharat
AAAnkit Agarwal
Ankit Agarwal
TGTyler Grimm
Tyler Grimm
LMLaine Mears
Laine Mears
The machining of free-form components by ball-end milling inherently produces surface error in the form of scallops. The objective of any free-form toolpath strategy is to balance productivity while minimizing scallop height to reduce surface error. Conventional machining strategies produce repeatable material patterns (constant scallop height) that may limit workpiece function in areas such as lubricity, directional anisotropy, and aesthetic appearance. These strategies also involve steady-state cuts, which allow accumulation of temperature, restrict the permissible depth and speed. In the present paper a novel complex stochastic toolpath strategy has been proposed that comprises pseudo-random circular contours concatenated into a smooth path. The approach enables continuous variation of chip load, force, and direction, and avoids conditions of continuous, periodic high cutting loads and heat accumulation. Based on initial testing, it has been observed that stochastic toolpaths are longer than conventional toolpaths. However, a decrease in average cutting loads enable reduction in cutting time with feed optimization. Additionally, the proposed strategy resulted in lower scallop height than conventional machining, thereby improving surface condition.

2 May 2023 in Microscopy
Verified
Journal Article
Closed access
PDF file
TGTyler Grimm
Tyler Grimm
LMLaine Mears
Laine Mears
Electrically assisted heat treatment is the process of applying an electric current to a sample during heat treatment. Literature has generally shown there to be a difference in the resulting effects of direct current (DC) current and highly transient current (i.e. electropulsing). However, these differences are poorly characterized. In situ transmission electron microscopy (TEM) observation of an AA7075 sample while DC and pulsed current were passed through it was performed herein to explore the effects of an electric current on precipitate development. Numerical simulation results indicate that the thermal response of the samples was very rapid, causing the sample to reach steady-state temperatures almost instantly. There does not appear to be any significant difference between the results of pulsed current application and DC current. Additionally, the failure mechanism of an electrical biasing TEM sample is explored.