Natalia Kovalska

Dr. Natalia Kovalska

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 January 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
DKDominik Knozowski
Dominik Knozowski
PSPradeep Vallachira Warriam Sasikumar
Pradeep Vallachira Warriam Sasikumar
PMPiotr Madajski
Piotr Madajski
Gurdial BluganGurdial Blugan
Gurdial Blugan
MGMaria Gazda
Maria Gazda
Monika Wilamowska-ZawłockaMonika Wilamowska-Zawłocka
Monika Wilamowska-Zawłocka
In this work, we present the characterization and electrochemical performance of various ternary silicon oxycarbide/graphite/tin (SiOC/C/Sn) nanocomposites as anodes for lithium-ion batteries. In binary SiOC/Sn composites, tin nanoparticles may be produced in situ via carbothermal reduction of SnO2 to metallic Sn, which consumes free carbon from the SiOC ceramic phase, thereby limiting the carbon content in the final ceramic nanocomposite. Therefore, to avoid drawbacks with carbon depletion, we used graphite as a substitute during the synthesis of precursors. The ternary composites were synthesized from liquid precursors and flake graphite using the ultrasound-assisted hydrosilylation method and pyrolysis at 1000 °C in an Ar atmosphere. The role of the graphitic component is to ensure good electric conductivity and the softness of the material, which are crucial for long term stability during alloying–dealloying processes. The presented approach allows us to increase the content of the tin precursor from 40 wt.% to 60 wt.% without losing the electrochemical stability of the final material. The charge/discharge capacity (at 372 mA g−1 current rate) of the tailored SiOC/C/Sn composite is about 100 mAh g−1 higher compared with that of the binary SiOC/Sn composite. The ternary composites, however, are more sensitive to high current rates (above 372 mA g−1) compared to the binary one because of the presence of graphitic carbon.

15 September 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
KSKamoladdin Saidov
Kamoladdin Saidov
Jamoliddin RazzokovJamoliddin Razzokov
Jamoliddin Razzokov
OPOdilkhuja Parpiev
Odilkhuja Parpiev
NYNur Sena Yuzbasi
Nur Sena Yuzbasi
NKNatalia Kovalska
Natalia Kovalska
OROlim Ruzimuradov
Olim Ruzimuradov
2H MoTe2 (molybdenum ditelluride) has generated significant interest because of its superconducting, nonvolatile memory, and semiconducting of new materials, and it has a large range of electrical properties. The combination of transition metal dichalcogenides (TMDCs) and two dimensional (2D) materials like hexagonal boron nitride (h-BN) in lateral heterostructures offers a unique platform for designing and engineering novel electronic devices. We report the fabrication of highly conductive interfaces in crystalline ionic liquid-gated (ILG) field-effect transistors (FETs) consisting of a few layers of MoTe2/h-BN heterojunctions. In our initial exploration of tellurium-based semiconducting TMDs, we directed our attention to MoTe2 crystals with thicknesses exceeding 12 nm. Our primary focus centered on investigating the transport characteristics and quantitatively assessing the surface interface heterostructure. Our transconductance (gm) measurements indicate that the very efficient carrier modulation with an ILG FET is two times larger than standard back gating, and it demonstrates unipolarity of the device. The ILG FET exhibited highly unipolar p-type behavior with a high on/off ratio, and it significantly increased the mobility in MoTe2/h-BN heterochannels, achieving improvement as one of the highest recorded mobility increments. Specifically, we observed hole and electron mobility values ranging from 345 cm2 V−1 s−1 to 285 cm2 V−1 s−1 at 80 K. We predict that our ability to observe the intrinsic, heterointerface conduction in the channels was due to a drastic reduction of the Schottky barriers, and electrostatic gating is suggested as a method for controlling the phase transitions in the few layers of TMDC FETs. Moreover, the simultaneous structural phase transitions throughout the sample, achieved through electrostatic doping control, presents new opportunities for developing phase change devices using atomically thin membranes.

20 April 2023 in Coatings
Verified
Journal Article
Open access
PDF file
NKNatalia Kovalska
Natalia Kovalska
AMAntonio Mulone
Antonio Mulone
Jordi SortJordi Sort
Jordi Sort
UKUta Klement
Uta Klement
Gurdial BluganGurdial Blugan
Gurdial Blugan
Wolfgang KautekWolfgang Kautek
Wolfgang Kautek
Fe-W-P coatings were deposited from a newly developed electrolytic bath. The effect of plating parameters, such as electrolyte current density and pH has been studied. It was found that the pH has a very strong effect on the phosphorous content of the coatings. Metallic-like, non-powdery alloys of Fe-W-P deposits with no cracks (lowly stressed) can be obtained at a lower pH (3), the composition changes to low phosphorus and high tungsten content, showing a matte, greyish, and rough surface. The applied current density also influences the morphology and the amount of phosphorous content. The deposits showed an amorphous structure for all samples with soft ferromagnetic properties.