Ferhat bouzerara

Dr. Ferhat bouzerara


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2016 in Desalination and Water Treatment
Verified
Journal Article
Open access
BGBoudjemaa Ghouil
Boudjemaa Ghouil
AHAbdelhamid Harabi
Abdelhamid Harabi
FBFerhat bouzerara
Ferhat bouzerara
NBNoureddine Brihi
Noureddine Brihi
There is a much current interest in the application of membranes in separation procedures because of their application in the treatment of big amounts of wastewaters. The use of ceramic membranes has many advantages such as a high thermal and a chemical stability, a pressure resistance, a long lifetime, and good defouling properties. Microfiltration (MF) and ultrafiltration are often used to remove particles, micro-organisms, and colloidal materials from suspensions. In this work, the supports for MF were prepared with local clays and calcite mixtures. The choice of these raw materials is based on their natural abundance (low price) and interesting microstructures. These supports were made by an extrusion technique in order to obtain tubular supports, which were afterward sintered at 1,250°C for 1 h. It has been found that the elaborated supports had interesting characteristics; an average pore size of about 4 μm and a porosity ratio around 50%. Moreover, the pore size distribution is almost homogenous (mono-modal type). The surface and the cross-section morphologies observed through a scanning electron microscope are also homogenous and do not present any macro defects (cracks, etc.). Moreover, these supports were tested with distilled water. A cross-flow microfiltration was performed. The result showed a good retention of supports turbidity.

1 December 2020 in Journal of the European Ceramic Society
Verified
Journal Article
Closed access
ABAmina Boulkrinat
Amina Boulkrinat
FBFerhat bouzerara
Ferhat bouzerara
AHAbdelhamid Harabi
Abdelhamid Harabi
KHKamel Harrouche
Kamel Harrouche
SSSara Stelitano
Sara Stelitano
AFAlberto Figoli
Alberto Figoli

22 March 2019 in Journal of the Australian Ceramic Society
Verified
Journal Article
Closed access
PDF file
CKCheikh Kadiri
Cheikh Kadiri
AHAbdelhamid Harabi
Abdelhamid Harabi
FBFerhat bouzerara
Ferhat bouzerara
LFLazhar Foughali
Lazhar Foughali
NBNoureddine Brihi
Noureddine Brihi
BBBoukhemis Boudaira
Boukhemis Boudaira

31 March 2023 in Membranes
Verified
Journal Article
Open access
PDF file
ZKZineb Khebli
Zineb Khebli
FBFerhat bouzerara
Ferhat bouzerara
NBNourddine Brihi
Nourddine Brihi
Alberto FIGOLIAlberto FIGOLI
Alberto FIGOLI
Fancesca RussoFancesca Russo
Fancesca Russo
SCSadek Chahredine
Sadek Chahredine
Multilayer ceramic membranes to be used for bacteria removal by filtration were prepared from ceramic materials. They consist of a macro-porous carrier, an intermediate layer and a thin separation layer at the top. Tubular and flat disc supports were prepared from silica sand and calcite (natural raw materials), using extrusion and uniaxial pressing methods, respectively. Making use of the slip casting technique, the silica sand intermediate layer and the zircon top-layer were deposited on the supports, in this order. The particle size and the sintering temperature for each layer were optimized to achieve a suitable pore size for the deposition of the next layer. Morphology, microstructures, pore characteristics, strength and permeability were also studied. Filtration tests were conducted to optimize the permeation performance of the membrane. Experimental results show that the total porosity and average pore size of the porous ceramic supports sintered at different temperatures within the range (1150–1300 °C), and lie in the ranges of 44–52% and 5–30 μm, respectively. For the ZrSiO4 top-layer, after firing at 1190 °C, a typical average pore size of about 0.3 μm and a thickness of about 70 μm were measured, while water permeability is estimated to a value of 440 lh−1m−2bar−1. Finally, the optimized membranes were tested in the sterilization of a culture medium. Filtration results show the efficiency of the zircon-deposited membranes for bacteria removal; indeed, the growth medium was found to be free of all microorganisms.

1 March 2016 in Desalination and Water Treatment
Verified
Journal Article
Open access
LFLazhar Foughali
Lazhar Foughali
SBSalaheddine Barama
Salaheddine Barama
AHAbedelhamid Harabi
Abedelhamid Harabi
FBFerhat bouzerara
Ferhat bouzerara
AGAbdelkrim Guechi
Abdelkrim Guechi
BBBoukhemis Boudaira
Boukhemis Boudaira
Porous ceramic separation membranes exhibit many excellent properties, such as a high structural durability, a good thermal stability, a long operational life, and an especially high chemical stability in the corrosive media. In order to prepare low-cost membranes, many researchers have used low-cost starting materials such as clay, dolomite, and kaolin. This work addresses the development of low-cost ceramic microfiltration membrane supports from inexpensive raw materials, such Sigue quartz sand (SQS) and sodium phosphate (SP), using a uniaxially dry compaction method. The prepared samples were sintered at different temperatures ranging between 900 and 1,400°C. The raw materials and the prepared samples were characterized using X-ray diffraction (XRD), optical microscopy, Hg-porosimetry, and tensile strength using a diametral compression test. Subsequently, the effect of sintering temperature and SP amounts on support proprieties, such as the shrinkage, the phase transformation, the porosity, and tensile strength, were also investigated. It was observed that with increasing sintering temperature, dimensions of sintered samples increased; this was due to the phase transformation. XRD confirmed that SQS was transformed into cristobalite phase when both the sintering temperature and the holding time were increased. The porosity and average pore size (APS) increased in all cases (2 and 3 wt% SP) in the range of temperatures between 1,100 and 1,400°C. For example, the porosity increased from 25.4 to 32.9%, and APS increases from 11 to 27 μm in the case of 3 wt% SP. The flexural strength was found to be acceptable. The value varied from 16 to 20 MPa, which corresponds well with the relatively high porosity and APS.

1 January 2024 in Processing and Application of Ceramics
Verified
Journal Article
Open access
BGBoudjemaa Ghouil
Boudjemaa Ghouil
ZKZineb Khebli
Zineb Khebli
FBFerhat bouzerara
Ferhat bouzerara
DZDounia Zermani
Dounia Zermani
CZChahinez Zitouni
Chahinez Zitouni
TKTarek Khennouf
Tarek Khennouf
This work presents the preparation of microfiltration (MF) membranes deposited on highly porous supports tailored for microfiltration applications. The supports were prepared from local Algerian clays and calcium carbonate, selected for their abundant availability. Subsequently, these supports underwent coating with microfiltration membrane using the slip casting method employing the same clay powder. The resulting membrane, sintered at 1100?C, exhibited desirable attributes including a thickness of approximately 27 ?m and an average pore size (APS) value of about 0.42 ?m, coupled with notable adhesion between the support and the membrane. Furthermore, physicochemical and microbiological tests were conducted on water samples to confirm the effectiveness of the membrane in microfiltration. The results show that the membrane is highly effective in removing turbidity, with a rejection rate of approximately 99%. The pH and conductivity of the water remain stable during filtration. Additionally, the membrane demonstrates significant efficiency in removing heavy metals, with rejection rates of about 68% for iron and 90% for aluminium, as well as it is effective in removing specific bacteria from water.