The stability of a double-row steel sheet pile cofferdam structure under soft ground conditions was investigated in this study, using the temporary cofferdam of the Shenzhen–Zhongshan cross-river channel as the engineering background. The stability of the cofferdam design solution was calculated with a model that incorporates factors such as the coordination of independent pile top displacement, as well as the m-value for backfilled sand and the thrown rock body. The internal force and displacement results of the cofferdam under different working conditions are obtained. And the entire construction process was analyzed using the finite element method. The results indicate that the overall stability and overturning stability of the cofferdam satisfy relevant safety requirements, with minimum safety factors of 1.744 and 1.400, respectively. The maximum displacement of the inner and outer steel sheet piles is 34 mm, the maximum bending moment is 249.30 kN·m, and the maximum shear force is 266.66 kN. The displacements of sheet piles were within an acceptable range, and the internal forces remained below the load capacity of the selected sheet pile type for the design. Based on these findings, the cofferdam structure can be considered safe and satisfying the specified requirements. This work may have instructive value for cofferdam design and construction.

The road construction sector urgently requires environmentally friendly, low-carbon, and high-performance base materials. Traditional materials exhibit issues of high energy consumption and carbon emissions, making it difficult for them to align with sustainable development requirements. While slag- and fly ash-based geopolymers demonstrate promising application potential in civil engineering, research on their application in road-stabilized soils remains insufficient. To address the high energy consumption and carbon emissions associated with conventional road base materials and to fill this research gap, this study investigated the utilization of industrial solid wastes through slag-based geopolymer and fly ash as stabilizers, systematically evaluating the pavement performance of two distinct soil types. Unconfined compressive strength tests and freeze–thaw cycling tests were conducted to elucidate the effects of stabilizer dosage, fly ash co-stabilization, and compaction degree on mechanical properties. The results demonstrated that the compressive strength of both stabilized soils increased significantly with higher slag-based geopolymer content, achieving peak values of 5.2 MPa (soil sample 1) and 4.5 MPa (soil sample 2), representing a 30% improvement over cement-stabilized soils with identical mix proportions. Fly ash co-stabilization exhibited more pronounced reinforcement effects on soil sample 2. At a 98% compaction degree, soil sample 1 maintained a stable 50% strength enhancement, whereas soil sample 2 displayed a dose-dependent exponential strength increase. Freeze–thaw resistance tests revealed the superior performance of soil sample 1, showing a loss of compressive strength (BDR) of 78% with 8% geopolymer stabilization alone, which improved to 90% after fly ash co-stabilization. For soil sample 2, the BDR increased from 64% to 80% through composite stabilization. This study confirms that slag/fly ash-based geopolymer-stabilized soils not only meet the strength requirements for heavy-traffic subbases and light-traffic base courses, but also demonstrates its great potential as a low-carbon and environmentally friendly material to replace traditional road base materials.

In shield tunneling, ensuring bonding performance at new-to-old concrete interfaces between segments and linings is crucial for composite lining stability. While extensive research exists on the mechanical bonding behavior of such interfaces, comparative studies on two prevalent treatment methods—scabbling and grooving—remain limited. This study systematically evaluates these techniques’ effects on interfacial bonding via direct shear tests, benchmarking against smooth-interface specimens. Complementary cohesive zone modeling simulations further analyze stress distribution and damage evolution during shear failure. The results demonstrate that scabbled specimens exhibit 10.5%~18.2% higher shear strength than grooved counterparts under increasing normal stress, with both treatments significantly enhancing load–transfer synergy through mechanical interlocking. Furthermore, the energy-based bilinear cohesive model accurately predicts full-interface behavior, providing practical guidance for interface treatment selection in tunneling engineering.

This paper introduces an alternative method for determining the shear strength parameters of concrete materials, specifically the rectangular section splitting method, to ascertain the shear strength parameters of concrete materials. Based on the Mohr–Coulomb failure criterion, formulas for calculating the cohesion (c) and the angle of internal friction (φ) of concrete materials are derived. Numerical simulation is employed to fit and solve for the coefficients involved in the formulas. Subsequently, the concrete rectangular section splitting method and direct shear tests are utilized to verify the derived formulas. The results indicate that there is a certain feasibility to the shear strength parameters obtained for concrete materials through the rectangular section splitting method. The cohesion (c) differs by approximately 3.65%, and the angle of internal friction (φ) differs by about 6.94% when compared to the shear strength parameters obtained through direct shear tests. This suggests that the rectangular section splitting method provides a viable approach for determining the shear strength parameters of concrete materials.

To determine the mechanical properties of the rock mass in the Nansha Branch, three in-situ tests (on-site pressure plate, borehole TV and acoustic wave, and borehole deformation methods) were carried out. Based on the deformation characteristics of the rock mass, the finite element numerical method is used to study the combined stress of the composite lining in the diversion tunnel. The results demonstrate that the deformation modulus values are similar by comparing them to tests of the pressure plate and borehole deformation method. It shows the accuracy and reliability of the deformation modulus obtained by the borehole deformation method. In addition, the deformation modulus of the borehole deformation method and wave velocity were fitted to obtain a power function relationship. The deformation modulus of the pelitic siltstones was estimated. After the Nansha Branch tunnel is filled with water, the maximum principal stress of the pipe piece is 1.953 Mpa in tensile stress, located at the outside of the waist on both sides of the pipe piece. The maximum principal stress of the reinforced concrete lining is 5.407 Mpa, located at the top and bottom inside. The maximum principal stresses have exceeded the standard tensile strength of both the pipe piece and reinforced concrete and are vulnerable to cracking. Special attention should be paid to the deformation of the above parts with regard to long-term operation.