Sub-nanometer materials have received wide attention due to their unique properties in recent years. Most studies focus on the preparation and properties investigation of the inorganic sub-nanometer materials, while there are few reports on organic especially polymeric sub-nanometer materials such as sub-nanometer fiber due to the obstacles with respect to fabricating such small nanofibers. In this work we prepare PAA nanofibers with diameters ranging from hundreds of nanometers down to sub-nanometer via electrospinning from a polyamic acid (PAA) with ultrahigh molecular weight. The morphologies and size of the electrospun ultrathin nanofibers are characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atomic force microscopy (AFM). AFM images combined with theoretic calculations show that sub-nanometer fiber of approximate 0.17–0.63 nm only containing one molecular chain was generated via electrospinning from ultra-dilute PAA solutions for the first time. These quite small sub-nanometer fibers would open a new area of electrospinning and provide further explorations on the production and application of electrospun sub-nanometer fibers with single molecular chains.

La–Mn bimetal oxide nanofibers, used as an adsorbent for the defluoridation of water, were synthesized by an electrospinning and heat treatment technology. The La–Mn bimetal oxide nanofiber adsorbent with a specific surface area of 35.064 m² g⁻¹ displayed a good defluoridation performance. Both the adsorption kinetics and equilibrium for fluoride (F⁻) uptake onto La–Mn bimetal oxide nanofibers were investigated. The kinetic studies established that the adsorption attained equilibrium at about 90 min, and the PSO kinetic model was ideal for the kinetic data under 20 and 50 mg L⁻¹. The Langmuir maximum F⁻ uptake was computed to be 189.39 mg g⁻¹ at 308 K and pH 3. A thermodynamic study affirmed a feasible, endothermic, spontaneous and entropy driven process of F⁻ adsorption towards La–Mn bimetal oxide nanofibers at the studied temperature range. Except for the competitive adsorption of PO₄ ³⁻ and F⁻, the presence of NO₃ ⁻, CO₃ ²⁻, Cl⁻ and SO₄ ²⁻ had little effect on fluoride removal. The La–Mn bimetal oxide adsorbent exhibited a good reusability.

The occurrence of fluoride contamination in drinking water has gained substantial concern owing to its serious threat to human health. Traditional adsorbents have shortcomings such as low adsorption capacity and poor selectivity, so it is urgent to develop new adsorbents with high adsorption capacity, renewable and no secondary pollution. In this work, magnetic electrospun La-Mn-Fe tri-metal oxide nanofibers (LMF NFs) for fluoride recovery were developed via electrospinning and heat treatment, and its defluoridation property was evaluated in batch trials. Modern analytical tools (SEM, BET, XRD, FTIR) were adopted to characterize the properties of the optimized adsorbent, i.e., LMF11 NFs with a La:Mn molar ratio of 1:1. The surface area calculated via BET method and pH_pzc assessed using pH drift method of LMF11 NFs were 55.81 m² g⁻¹ and 6.47, respectively. The results indicated that the adsorption amount was highly dependent on the pH of the solution, and reached the highest value at pH = 3. The kinetic behavior of defluoridation on LMF11 NFs was dominated by the PSO model with the highest fitted determination coefficients of 0.9999. Compared with the other three isotherm models, the Langmuir model described defluoridation characteristics well with larger correlation coefficients of 0.9997, 0.9990, 0.9987 and 0.9976 at 15 °C, 25 °C, 35 °C and 45 °C, respectively. The optimized LMF11 NFs exhibited superior monolayer defluoridation capacities for 173.30–199.60 mg F⁻/g at pH 3 at 15–45 °C according to the Langmuir isotherm model. A thermodynamic study proved that the defluoridation by LMF11 NFs is a spontaneous, endothermic along with entropy increase process. In addition, the LMF11 NFs still showed high defluoridation performance after three reused cycles. These findings unveil that the synthesized LMF11 NFs adsorbent is a good adsorbent for fluoride remediation from wastewater owing to its low cost, high defluoridation performance and easy operation.

The performance of a Ce(III)-4,4′,4″-((1,3,5-triazine-2,4,6-triyl) tris (azanediyl)) tribenzoic acid–organic framework (Ce-H3TATAB-MOFs) for capturing excess fluoride in aqueous solutions and its subsequent defluoridation was investigated in depth. The optimal sorption capacity was obtained with a metal/organic ligand molar ratio of 1:1. The morphological characteristics, crystalline shape, functional groups, and pore structure of the material were analyzed via SEM, XRD, FTIR, XPS, and N₂ adsorption–desorption experiments, and the thermodynamics, kinetics, and adsorption mechanism were elucidated. The influence of pH and co-existing ions for defluoridation performance were also sought. The results show that Ce-H3TATAB-MOFs is a mesoporous material with good crystallinity, and that quasi-second kinetic and Langmuir models can describe the sorption kinetics and thermodynamics well, demonstrating that the entire sorption process is a monolayer-governed chemisorption. The Langmuir maximum sorption capacity was 129.7 mg g⁻¹ at 318 K (pH = 4). The adsorption mechanism involves ligand exchange, electrostatic interaction, and surface complexation. The best removal effect was reached at pH 4, and a removal effectiveness of 76.57% was obtained under strongly alkaline conditions (pH 10), indicating that the adsorbent has a wide range of applications. Ionic interference experiments showed that the presence of PO₄³⁻ and H₂PO₄⁻ in water have an inhibitory effect on defluoridation, whereas SO₄²⁻, Cl⁻, CO₃²⁻, and NO₃⁻ are conducive to the adsorption of fluoride due to the ionic effect.