Alojz Kopacik

Prof. Alojz Kopacik

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Ján ErdélyiJán Erdélyi
Ján Erdélyi
AKAlojz Kopacik
Alojz Kopacik
Peter KyrinovičPeter Kyrinovič
Peter Kyrinovič
Weather conditions and different operational loads often cause changes in essential parts of engineering structures, and this affects the static and dynamic behavior and reliability of these structures. Therefore, geodetic monitoring is an integral part of the diagnosis of engineering structures and provides essential information about the current state (condition) of the structure. The development of measuring instruments enables deformation analyses of engineering structures using non-conventional surveying methods. Nowadays, one of the most effective techniques for spatial data collection is terrestrial laser scanning (TLS). TLS is frequently used for data acquisition in cases where three-dimensional (3D) data with high resolution is needed. Using suitable data processing, TLS can be used for static deformation analysis of the structure being monitored. For dynamic deformation measurements (structural health monitoring) of bridge structures, ground-based radar interferometry and accelerometers are often used for vibration mode determination using spectral analysis of frequencies. This paper describes experimental deformation monitoring of structures performed using TLS and ground-based radar interferometry. The procedure of measurement, the analysis of the acquired spatial data, and the results of deformation monitoring are explained and described.

19 April 2017 in Applied Geomatics
Verified
Journal Article
Closed access
PDF file
ERErdélyi
Erdélyi
JÁJán
Ján
AKAlojz Kopacik
Alojz Kopacik
ILImrich Lipták
Imrich Lipták
PKPeter Kyrinovič
Peter Kyrinovič

14 September 2022 in Remote Sensing
Verified
Journal Article
Open access
PDF file
Richard HontiRichard Honti
Richard Honti
Ján ErdélyiJán Erdélyi
Ján Erdélyi
AKAlojz Kopacik
Alojz Kopacik
Building information models (BIM) in the civil industry are very popular nowadays. The basic information of these models is the 3D geometric model of a building structure. The most applied methodology to model the existing buildings is by generating 3D geometric information from point clouds provided by laser scanners. The fundamental principle of this methodology is the recognition of structures shaped in basic geometric primitives, e.g., planes, spheres, and cylinders. The basic premise of the efficiency of this methodology is the automation of detection, since manual segmentation of a point cloud can be challenging, time-consuming, and, therefore, inefficient. This paper presents a novel algorithm for the automated segmentation of geometric shapes in point clouds without needing pre-segmentation. With the designed algorithm, structures formed in three types of basic geometrical primitive can be identified and segmented: planar (e.g., walls, floors, ceilings), spherical (e.g., laser scanner reference targets), and cylindrical (e.g., columns, pillars, piping). The RANSAC paradigm partially inspires the proposed algorithm; however, various modifications must be made. The algorithm was tested on several point clouds and was compared with the standard RANSAC algorithm; this part is described in the last section of the paper. One of the tests was performed on a double cylinder-shaped test object, the parameters (radius and height) of this object were available with high accuracy (0.1 mm), and the differences between the known and estimated parameters were below 0.5 mm in each case, indicating the correctness of the proposed algorithm. Also, a comparison with the standard RANSAC algorithm was performed, where the algorithm proposed showed better results than the standard RANSAC algorithm. The segmentation quality was, on average, increased from 50% to 100%.

15 June 2016 in IEEE Sensors Journal
Verified
Journal Article
Closed access
AKAlojz Kopacik
Alojz Kopacik
PKPavol Kajánek
Pavol Kajánek
ILImrich Liptak
Imrich Liptak
Inertial measuring systems (IMSs) enable determination of 3-D position and trajectory on a base of the actual measured acceleration and angular velocity. Measurements with the inertial sensors are influenced by errors from used sensors. Because of the principle of calculation of a position based on the recursive algorithm, there is an accumulation of systematic error, which causes a rapid decreasing of the position accuracy hand in hand with a measuring time. This paper deals with the suggestion of the model for data processing, which enables to eliminate systematic errors of sensors; thereby, the position accuracy is increased. For this purpose, an optical rotational-speed sensor was introduced and the additional measurement was realized with it in combination with the two IMSs located on the common baseline. Measurements from optical rotational-speed sensor were used in a combination with the accelerometers for their higher long-term accuracy. This combination enables to eliminate errors from the accelerometers even after the first integration process. Using the pair of IMSs located on the common baseline, the requirements (constraints) of the geometric relation of two coordinate systems of these IMSs were implemented into the model for data processing. These constraints were applied for correction of the position and orientation. As a part of the suggested model, an algorithm for identification of the dynamic phases was realized. This algorithm identified an actual dynamic phase of the system on a basis of the actual measured acceleration and angular velocity. This information was used for an adjustment of the processing model.

9 March 2018 in Applied Geomatics
Verified
Journal Article
Closed access
PDF file
Ján ErdélyiJán Erdélyi
Ján Erdélyi
AKAlojz Kopacik
Alojz Kopacik
PKPeter Kyrinovič
Peter Kyrinovič

1 August 2018 in Pollack Periodica
Verified
Journal Article
Closed access
Richard HontiRichard Honti
Richard Honti
JEJán Erdélyi
Ján Erdélyi
AKAlojz Kopacik
Alojz Kopacik
Recently, attempts have been made to automate data acquisition, which is also related to efforts to automate data processing. The paper deals with the automation of terrestrial laser scanning data processing. The approaches for point cloud segmentation are briefly described. An algorithm based on random sample consensus is proposed for automated plane identification and plane segmentation from point clouds. The proposed approach was tested by processing point clouds; the results of the testing are also described. Based on the proposed algorithm, a standalone application for automated plane segmentation from laser scanner data using Matlab® software was developed.