Pavol Kajánek

Mr. Pavol Kajánek

Department of Surveying, Slovak University of Technology in Bratislava, Bratislava, Bratislavský, Slovakia
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 June 2016 in IEEE Sensors Journal
Verified
Journal Article
Closed access
AKAlojz Kopacik
Alojz Kopacik
PKPavol Kajánek
Pavol Kajánek
ILImrich Liptak
Imrich Liptak
Inertial measuring systems (IMSs) enable determination of 3-D position and trajectory on a base of the actual measured acceleration and angular velocity. Measurements with the inertial sensors are influenced by errors from used sensors. Because of the principle of calculation of a position based on the recursive algorithm, there is an accumulation of systematic error, which causes a rapid decreasing of the position accuracy hand in hand with a measuring time. This paper deals with the suggestion of the model for data processing, which enables to eliminate systematic errors of sensors; thereby, the position accuracy is increased. For this purpose, an optical rotational-speed sensor was introduced and the additional measurement was realized with it in combination with the two IMSs located on the common baseline. Measurements from optical rotational-speed sensor were used in a combination with the accelerometers for their higher long-term accuracy. This combination enables to eliminate errors from the accelerometers even after the first integration process. Using the pair of IMSs located on the common baseline, the requirements (constraints) of the geometric relation of two coordinate systems of these IMSs were implemented into the model for data processing. These constraints were applied for correction of the position and orientation. As a part of the suggested model, an algorithm for identification of the dynamic phases was realized. This algorithm identified an actual dynamic phase of the system on a basis of the actual measured acceleration and angular velocity. This information was used for an adjustment of the processing model.

3 June 2014 in Geoinformatics FCE CTU
Verified
Journal Article
Open access
PDF file
PKPavol Kajánek
Pavol Kajánek
Inertial navigation system (INS) is a self-contained navigation technique. Its main purpose is to determinate the position and the trajectory of the object´s movement in space. This technique is well represented not only as a supplementary method (GPS/INS integrated system) but as an autonomous system for navigation of vehicles and pedestrians, also. The aim of this paper is to design a test for low-cost inertial measurement units. The test results give us information about accuracy, which determine the possible use in indoor navigation or other applications. There are described some methods for processing the data obtained by inertial measurement units, which remove noise and improve accuracy of position and orientation.

29 February 2024 in Sensors
Verified
Journal Article
Open access
PDF file
PKPavol Kajánek
Pavol Kajánek
AKAlojz Kopacik
Alojz Kopacik
Peter KyrinovičPeter Kyrinovič
Peter Kyrinovič
Ján ErdélyiJán Erdélyi
Ján Erdélyi
Marian MarčišMarian Marčiš
Marian Marčiš
Marek FraštiaMarek Fraštia
Marek Fraštia
For the calibration of linear scales, comparators are generally used. Comparators are devices that enable the movement of an evaluation apparatus over a calibrated scale along a linear base with high precision. The construction of a comparator includes a movable carriage that carries the device for the evaluation of the position of the given edge of the line scale relative to the beginning of the scale. In principle, it involves a camera capturing the scale of the measurer, where the position of the camera’s projection center is measured using an interferometer. This article addresses the development of a comparator assembled from low-cost components, as well as the description of systematic influences related to the movement of individual parts of the system, such as the inclination and rotation of the camera and directional and height deviations during the carriage’s movement. This article also includes an evaluation of the edge of the given scale with subpixel accuracy, addressing distortion elimination and excluding the influences of impurities or imperfections on the scale. The proposed solution was applied to linear-scale measurers, such as leveling rods with coded and conventional scales and measuring tapes. The entire process of measurement and evaluation was automated.

20 October 2020
Verified
Book Chapter
Closed access
PDF file
PKPavol Kajánek
Pavol Kajánek
AKAlojz Kopacik
Alojz Kopacik
Ján ErdélyiJán Erdélyi
Ján Erdélyi
PKPeter Kyrinovič
Peter Kyrinovič

1 June 2022 in Slovak Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
JBJán Brindza
Ján Brindza
PKPavol Kajánek
Pavol Kajánek
JEJán Erdélyi
Ján Erdélyi
The article deals with developing and testing a low-cost measuring system for simultaneous localisation and mapping (SLAM) in an indoor environment. The measuring system consists of three orthogonally-placed 2D lidars, a robotic platform with two wheel speed sensors, and an inertial measuring unit (IMU). The paper describes the data processing model used for both the estimation of the trajectory of SLAM and the creation of a 3D model of the environment based on the estimated trajectory of the SLAM. The main problem of SLAM usage is the accumulation of errors caused by the imperfect transformation of two scans into each other. The data processing developed includes an automatic evaluation and correction of the slope of the lidar. Furthermore, during the calculation of the trajectory, a repeatedly traversed area is identified (loop closure), which enables the optimisation of the trajectory determined. The system was tested in the indoor environment of the Faculty of Civil Engineering of the Slovak University of Technology in Bratislava.

1 January 2023 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
PKPavol Kajánek
Pavol Kajánek
JBJán Brindza
Ján Brindza
AKAlojz Kopacik
Alojz Kopacik
Ján ErdélyiJán Erdélyi
Ján Erdélyi
Peter KyrinovičPeter Kyrinovič
Peter Kyrinovič
The article presents a proposed mapping system that uses three stably located 2D lidars to map the indoor environment and create a model. Each lidar has its sensor frame, whose position and orientation change during the measurement. For this purpose, simultaneous mapping and localisation SLAM is used. By transforming lidar scans into a global coordinate system, the system’s change of position and orientation is calculated. The accuracy of the transformation is affected by the surrounding environment, where narrow straight corridors make it challenging to calculate the transformation. Errors in the determination of transformation parameters (translation and rotation) accumulate in the calculated position and orientation of the system. These errors are then transferred to the created model of the environment. The accuracy of determining the position and orientation of the system is increased by using additional sensors such as an inertial measuring unit, speed sensor, and stereo camera. Part of the data processing is identifying the repeatedly traversed area by optimising the trajectory and model. The proposed system is low-cost, portable, and allows 2D lidar when navigating and mapping the surrounding 3D space. The system’s accuracy is evaluated based on comparison results with the reference model.