This paper addresses the problem of underestimated temperature measurements in practical proton exchange membrane (PEM) electrolyzer engineering due to heat losses by enhancing the existing second-order RC equivalent circuit model of PEM electrolyzers. We present a novel engineering circuit model for PEM electrolyzers, incorporating the effects of heat losses from gases and pipelines. The objective is to enhance the model’s ability to predict electrolyzer performance and align control strategies with the realities of engineering practice. However, the PEM electrolyzer model is complex, being time-varying and nonlinear due to multi-physics field coupling. The parameters of the equivalent circuit are changed by the electrical energy input and its own state. To tackle the problem of parameter variation, firstly, a recursive identification algorithm is employed to estimate the internal equivalent circuit parameters of the engineering model. Then, the additional resistance is fitted according to the relationship between heat loss and current to complete the engineering circuit model identification. Finally, using MATLAB to construct an engineering model and validate the effectiveness of the proposed identification algorithm.
The issue of sub-module (SM) capacitor voltage unbalance is a hot topic in the current research into the modular multilevel converter (MMC). An excellent strategy comprises mitigating the SM capacitor voltage imbalance by adjusting the SM on time. The traditional capacitor voltage balancing control regulates the speed to maintain accuracy. A unique SM capacitor voltage balancing control strategy is presented in this paper and is based on conventional capacitor voltage balance management and neural network prediction. Firstly, the SM capacitor voltage and arm current are speculated by operating the time series forecasting technique in real time, considering the dynamic changes in the SM capacitor voltage and arm current. Secondly, the SM capacitor voltage distinction between the actual and theoretical value is determined, and a deviation’s mixed Gaussian distribution is established to estimate its compensation voltage. Thirdly, the SM triggering sequence is anticipated by using the neural network along with the pilot values of the SM capacitor voltage, arm current, and the offset compensation value, and the control is executed. Finally, a three-phase, six-leg, eight-module, nine-level MMC model is built to verify the feasibility of the suggested approach.
In order to address the issue of a solar utilization system with low efficiency, this paper designs a new solar conversion system based on photovoltaic concentration and spectral splitting. The system concentrates sunlight through a Fresnel lens and uses a hollow concave cavity to evenly distribute the incident energy flow. The spectral splitting medium separates the useful irradiance for the PV cell from those wavelengths that are more suited to heat generation. By considering the available wavelength of photovoltaic cells, the GaAs cell and a ZnO nanofluid were selected for this paper. It was found that installing the hollow concave cavity improved the spot uniformity of the PV cell surface by 17%. The output efficiency of the system under various circumstances was analyzed. The results show that at a concentration ratio of 50 and a light intensity of 1000 W/m2, photoelectric conversion efficiency increased by 0.81%. When compared to direct concentration, the photoelectric conversion efficiency increased by at least 7%. Meanwhile, the comprehensive electrical efficiency was 36.7%, which is higher than that of the normal concentration PV and comprehensive thermal system.
Modular Multilevel Converters (MMCs) are widely used in HV and MVDC transmission. However, their application causes the voltage level to increase, and the number of sub-modules also increases. Problems such as circulating currents and sub-module voltage fluctuations should not be neglected. Considering the coupling relationship between the circulating current and the sub-module capacitor voltage fluctuation, the circulating current suppressing controller (CCSC) and the active power filter (APF) techniques are used to solve the two problems mentioned above simultaneously. Firstly, in order to reduce the influence of clutter on the tracking of the target components of the CCSC, a Second-Order Generalized Integrator (SOGI) is added to accurately lock the main 2nd and 4th harmonic components in the circulating current. Secondly, an APF is added on top of the circulating current suppression, and the two methods can be mutually reinforcing in their roles. The APF applies the strategy of current inner-loop dominant and voltage outer-loop bias control. It is regarded as a whole for absorbing the voltage fluctuations of the sub-module and also eliminates the error caused by the inductive voltage. Finally, the effectiveness of the above method is verified in MATLAB/Simulink, which demonstrates that the proposed method provides better suppression of both circulating current and sub-module voltage fluctuations compared to the conventional MMC that only incorporates APF.
Single photovoltaic (PV) and photothermal (PT) technologies in solar energy applications are limited to the conversion of visible light and high-quality infrared spectra, respectively; this limitation results in relatively low energy utilization efficiency. In contrast, liquid spectrum-splitting technology enables the separation and conversion of various spectral bands, with the composition of the medium playing a pivotal role in the efficient utilization of the full spectrum. Compared to previous static spectral-splitting systems, this study introduces a dynamic nanofluid concentration control mechanism, which actively balances PV and PT contributions based on real-time solar conditions, achieving higher adaptability and efficiency. This study proposes a concentrated photovoltaic-thermal (CPVT) system based on the variable concentration of spectrum-splitting media, employing a concave-bottom, hollow pipeline structure. By introducing nanofluids with varying concentrations, we measured and analyzed spot uniformity and transmittance, comparing the system's absorption properties for infrared light to its transmittance properties for visible light. A tunable model for photoelectric and photothermal-electric conversion was constructed, enabling the evaluation of differences in thermal and electrical performance. The results indicate that, within the designed spectrum-splitting pipeline, increases in nanofluid concentration correlate with improvements in both temperature and thermal efficiency. However, the photovoltaic efficiency decreased at higher concentrations. When the concentration reached approximately 280 ppm, the system achieved a peak comprehensive efficiency of 50.63%, demonstrating its superiority in adaptability and full-spectrum utilization compared to previous CPVT systems. As the concentration increased to 420 ppm, light transmittance nearly approached zero, resulting in a peak in thermal efficiency. This variability in concentration endows the system with a flexible capacity to modulate both thermal and electrical outputs, offering significant potential for further development.
To address the limitations of empirical parameter tuning in the outer-loop PI controller and the high computational burden of the inner loop in conventional dual-loop control for modular multilevel converters, a coordinated control strategy is proposed that integrates particle swarm optimization-based fuzzy PI control with finite-state hierarchical model predictive control. The outer loop employs a two-dimensional fuzzy PI controller, in which error and error variation are selected as inputs. The quantization and proportional factors are optimally determined through an offline global search using particle swarm optimization, enabling adaptive parameter adjustment and improving the tracking accuracy of current reference signals under varying operating conditions. The inner loop adopts finite-state model predictive control, where AC-side phase voltages and total arm voltages are predicted using a reverse calculation method. Based on objective function minimization combined with integer rounding, the required number of submodules for the upper and lower arms is determined. Circulating current suppression is subsequently introduced to mitigate steady-state deviations on the AC side, and predictive submodule voltage grouping and sorting are applied to balance capacitor voltages. This approach eliminates the need for weighting factor design and effectively reduces computational complexity. Finally, simulations carried out in MATLAB/Simulink confirm the effectiveness of the proposed strategy.