With urban and rural infrastructure development, the power system is being forced to operate at or near its full capacity. This paper proposes four new methodologies to find the solution to the optimal reactive power dispatch (ORPD) problem, considering the capabilities of modern DFIG-based WTs and VSI-based solar P.V. The proposed formulation considers the techno-economic objective functions, specifically the minimization of the active and reactive power cost and the maximization of reactive power reserve. This leads to an effective solution to the probabilistic multi-objective ORPD (PMO-ORPD) problem, especially in the context of modern wind farms (W.F.s) and solar P.V. The proposed formulations are necessary for effectively managing power systems with renewable energy sources and contribute to developing efficient and sustainable power systems. Additionally, this study employs probabilistic mathematical modeling that incorporates Weibull, lognormal, and normal probability distribution functions (PDFs) to represent uncertainties in the wind, solar, and load demand. Monte-Carlo simulation (MCS) is employed to generate probabilistic scenarios, allowing for a comprehensive analysis of the PMO-ORPD problem. A new two-phase (ToP) multi-objective evolutionary algorithm is proposed, which incorporates the superiority of feasibility constraints to effectively solve the probabilistic multi-objective optimal reactive power dispatch (PMO-ORPD) problem. From the analysis and comparison of simulation results, it has been observed that the proposed algorithm effectively solves the deterministic and PMO-ORPD problems.

The need for high-speed communication has created a way to design THz antennas that operate at high frequencies, speeds, and data rates. In this manuscript, a THz MIMO antenna is designed using a metamaterial. The two-port antenna design proposed uses a complementary split-ring resonator patch. The design results are also compared with a simple patch antenna to show the improvement. The design shows a better isolation of 50 dB. A broadband width of 8.3 THz is achieved using this complementary split-ring resonator design. The percentage bandwidth is 90%, showing an ultrabroadband response. The highest gain of 10.34 dB is achieved with this design. Structural parametric optimization is applied to the complementary split-ring resonator MIMO antenna design. The designed antenna is also optimized by applying parametric optimization to different geometrical parameters. The optimized design has a 20 µm ground plane, 14 µm outer ring width, 6 µm inner ring width, and 1.6 µm substrate thickness. The proposed antenna with its broadband width, high gain, and high isolation could be applied in high-speed communication devices.

This article reports a multi-point curvature sensor system based on multiplexed optical fiber Fabry-Perot interferometric (FPI) sensor devices and a microwave photonics interrogation technique. The FPI sensor is fabricated with the assistance of a capillary tube, where a short section of the capillary is sandwiched between two single-mode fibers, forming the air-gap Fabry-Perot cavity. Bending of the FPI device leads to changes in the fringe contrast of its reflection spectrum. Based on the microwave photonics filtering technique, variations of the fringe contrast are encoded into the changes in the peak magnitude of the passband in the frequency response of the FPI device. By multiplexing such FPI devices with different cavity lengths, multi-point measurements of curvature can be realized by tracking changes in corresponding passbands in the frequency response of the system. The FPI curvature sensor is easy-to-manufacture and cost-effective, and the microwave photonics-based system provides an alternative and robust solution to interrogating the multiplexed FPI sensors for multi-point curvature sensing that could be desired in structural health monitoring, human-machine interface sensing, and other related fields.

The optical response of a graphene oxide integrated silicon micro-ring resonator (GOMRR) to a range of vapour phase Volatile Organic Compounds (VOCs) is reported. The response of the GOMRR to all but one (hexane) of the VOCs tested is significantly higher than that of the uncoated (control) silicon MRR, for the same vapour flow rate. An iterative Finite Difference Eigenmode (FDE) simulation reveals that the sensitivity of the GO integrated device (in terms of RIU/nm) is enhanced by a factor of ~2, which is coupled with a lower limit of detection. Critically, the simulations reveal that the strength of the optical response is determined by molecular specific changes in the local refractive index probed by the evanescent field of the guided optical mode in the device. Analytical modelling of the experimental data, based on Hill-Langmuir adsorption characteristics, suggests that these changes in the local refractive index are determined by the degree of molecular cooperativity, which is enhanced for molecules with a polarity that is high, relative to their kinetic diameter. We believe this reflects a molecular dependent capillary condensation within the graphene oxide interlayers, which, when combined with highly sensitive optical detection, provides a potential route for discriminating between different vapour phase VOCs.