Luis Paulo Brasil de Souza

Dr. Luis Paulo Brasil de Souza

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 May 2023 in Geoenergy Science and Engineering
Verified
Journal Article
Closed access
LSLuis Paulo Brasil de Souza
Luis Paulo Brasil de Souza
GFGuilherme Rezende Bessa Ferreira
Guilherme Rezende Bessa Ferreira
ICIsabel Camerini
Isabel Camerini
TCTiago de Magalhães Correia
Tiago de Magalhães Correia
MRMateus Gheorghe de Castro Ribeiro
Mateus Gheorghe de Castro Ribeiro
JBJoão Humberto Guandalini Batista
João Humberto Guandalini Batista

31 December 2024 in Wave Motion
Verified
Journal Article
Closed access
LSLuis Paulo Brasil de Souza
Luis Paulo Brasil de Souza
JHJuan Andrés Santisteban Hidalgo
Juan Andrés Santisteban Hidalgo
TCTiago de Magalhães Correia
Tiago de Magalhães Correia
ICIsabel Camerini
Isabel Camerini
GFGuilherme Rezende Bessa Ferreira
Guilherme Rezende Bessa Ferreira
ABArthur Braga
Arthur Braga

1 December 2020 in Rio Oil and Gas Expo and Conference
Verified
Journal Article
Closed access
RARafael Valladares De Almeida
Rafael Valladares De Almeida
TCTiago de Magalhães Correia
Tiago de Magalhães Correia
JHJuan Andres Santisteban Hidalgo
Juan Andres Santisteban Hidalgo
ICIsabel Camerini
Isabel Camerini
BSBruno Greco De Sousa
Bruno Greco De Sousa
LSLuis Paulo Brasil de Souza
Luis Paulo Brasil de Souza

1 January 2023 in Matéria (Rio de Janeiro)
Verified
Journal Article
Open access
PDF file
LSLuis Paulo Brasil de Souza
Luis Paulo Brasil de Souza
DPDario Prada Parra
Dario Prada Parra
JRJosé Alan Foicinha Raiol
José Alan Foicinha Raiol
ABArthur Braga
Arthur Braga
LRLeonardo Dantas Rodrigues
Leonardo Dantas Rodrigues
The loads acting on mechanical components are usually complex, and the more traditional fatigue analysis criteria may be non-conservative, especially in out-of-phase and non-proportional loadings. Many multiaxial fatigue models have been developed and need to be experimentally validated. This work describes the load control mechanism of a low-cost electromechanical multiaxial fatigue testing machine, which applies variable axial and torsional loads. A load cell interconnected to the motor control system was manufactured and instrumented with extensometers. For the axial load, a four-bar mechanism coupled to a power screw was designed to apply alternating axial loads, thus ensuring a higher load frequency and preservation of the motor, which will not need to alternate its direction of rotation. The machine’s control system, focused on out-phase loading, is based on the data sent by the load cell and pulse encoders per degree for each motor, ensuring good accuracy in applied loads. Tests were carried out to check the system’s response, in which it was possible to apply load curves of torque and axial force in different phase shift angle. Therefore, several existing multiaxial fatigue models can be tested with good reliability.

3 May 2024 in Geoenergy Science and Engineering
Verified
Journal Article
Closed access
TCTiago de Magalhães Correia
Tiago de Magalhães Correia
LSLuis Paulo Brasil de Souza
Luis Paulo Brasil de Souza
GFGuilherme Rezende Bessa Ferreira
Guilherme Rezende Bessa Ferreira
ICIsabel Camerini
Isabel Camerini
JHJuan Andrés Santisteban Hidalgo
Juan Andrés Santisteban Hidalgo
LSLuisa Nogueira de Azeredo Coutinho Soares
Luisa Nogueira de Azeredo Coutinho Soares

18 February 2026 in Ultrasonics
Verified
Journal Article
Open access
AKAlan Kubrusly
Alan Kubrusly
LSLuis Paulo Brasil de Souza
Luis Paulo Brasil de Souza
Fotis KopsaftopoulosFotis Kopsaftopoulos
Fotis Kopsaftopoulos
According to acoustoelasticity, initial stress affects the propagation characteristics of ultrasonic waves. Investigation of the acoustoelastic effect on guided waves has been virtually restricted to states of axial stresses. Here, the effect of shear stress in each plane of an aluminum plate is analyzed utilizing the semi-analytical finite element method. Generally, the dependence of the dispersion curves on the shear stresses is considerably less pronounced than on axial stresses. Nonetheless, it presents a predominant quadratic behavior with the stress magnitude, which can be explained by the decomposition of the shear stress as tensile and compressive stresses. Furthermore, shear introduces coupling between guided wave modes, which is intensified at the frequencies where the dispersion curves originally intersect, and under shear veer away, presenting high sensitivity. Coupling can occur between modes of opposite or same symmetry, or between Lamb and SH modes. The latter suggests a new measuring principle which relies on the ratio of the coupled components. The ideal frequency-thickness for this end is approximately 3300 kHzmm for shear stress within the plate's horizontal plane, and approximately 2100 kHzmm for shear stress perpendicular to the propagation direction, due to the coupling of the S0 mode with the SH0 and SH1 modes, respectively.