Due to the need for comprehensive transportation hub construction, an existing bridge in a bustling urban area with an operation duration of 25 years was required to be demolished. Based on Life Cycle Assessment (LCA), this paper proposes a scheme of “Self-propelled modular transporter (SPMT) technology + large segment cutting” to compare the carbon emissions of demolition schemes qualitatively and quantitatively. To ensure structural safety during demolition, the finite element analysis was used to simulate the entire demolishing process, and measuring points were set up to monitor the deformation of the main girder in real time under various demolition conditions. The results indicate that the scheme of SPMT has the lowest carbon emissions during the demolition stage. Additionally, the long-term prestress loss shall be considered when demolishing existing bridges; the suggested 25% proportional value for the long-term prestress loss of the Caitian Bridge is appropriate, which is determined by comparing the calculated results from various formulas. The values of the calculated and measured deformations of the main girder under different working conditions are in good agreement, with errors mostly within 10% and a maximum of no more than 14.7%. The demolition of the entire bridge was completed in a total of 28 h with little noise and pollution, and the impact on daily traffic was avoided, proving that the proposed “SPMT technology + large segment cutting” scheme is safe, efficient, and achieves the goal of green, environmentally friendly, and rapid demolition.
In this study, the graded hierarchical hexagonal honeycomb (GHHH) integrating gradient design and hierarchical design was fabricated using the 3D-printing technique, and its in-plane elastic properties were investigated theoretically, experimentally, and numerically. Theoretical solutions were developed based on the Euler beam theory to predict the effective elastic modulus and Poisson’s ratio of GHHH, and theoretical values were in good agreement with the experimental and numerical results. The effect of gradient design and hierarchical design on the in-plane elastic properties of GHHH was also analyzed and compared. Results showed that the hierarchical design has a more significant effect on Poisson’s ratio and adjusting the internal forces of GHHH compared with the gradient design. In addition, it was found that GHHH exhibited higher stiffness compared with regular hexagonal honeycomb (RHH), graded hexagonal honeycomb (GHH), and vertex-based hierarchical hexagonal honeycomb (VHHH) under the constraint of the same relative density, respectively. Specifically, the effective elastic modulus of GHHH can be enhanced by 119.82% compared to that of RHH. This research will help to reveal the effect of integrating hierarchical design and gradient design on the in-plane elastic properties of honeycombs.
This paper presents an in-depth analysis of the mechanical behavior and joint shear capacity optimization of segmental U-shaped bridges, with a focus on the application of precast segmental techniques in the construction of U-beam bridges widely used in urban rail transit networks. This study further explores the roles of key position distribution and size in the overall stability and service behavior of such structures. Considering the critical case study of the Colombia Bogotá Metro Line 1 project, finite element modeling was carried out using ABAQUS 6.14 to simulate concrete material behaviors and to evaluate the stress–strain relationship in accordance with the concrete plastic damage model and existing standards. This research identifies the significant contribution of keys in minimizing deformation and enhancing shear capacity, demonstrating the pivotal influence of shear key design on the mechanical behavior of segmental bridges. By calculating the shear capacity under different cases, this study provides recommendations on key distributions and dimensions that optimize joint shear capacities, indicating that augmenting key size within the web plate section decisively reinforces the bridge’s mechanical resilience.
This study aims to provide an effective method to study the behavior of a steel–concrete composite deck. First, the structural characteristics of the composite deck and the challenges arising in the computational analysis of the structure using general software are described. Then, an LPGE element that combines the plate element and the girder element into one element to conveniently construct the model with high computation efficiency is proposed. Based on the principle of multivariate field function, the constraint matrix for the plate and girder and the stiffness matrix for the LPGE are derived. The LPGE method is used to study the behavior of the composite deck through the computation of a steel truss arch bridge. The computation results are compared with the results obtained in ANSYS and the test results to verify the correctness and effectiveness of the LPGE method. The results of the paper offer references for the analysis of steel–concrete composite decks.