We synthesized Ni/Si-codoped TiO2 nanostructures for photoelectrochemical (PEC) water splitting, by electrochemical anodization of Ti-1Ni-5Si alloy foils in ethylene glycol/glycerol solutions containing a small amount of water. The effects of annealing temperature on PEC properties of Ni/Si-codoped TiO2 photoanode were investigated. We found that the Ni/Si-codoped TiO2 photoanode annealed at 700 °C had an anatase-rutile mixed phase and exhibited the highest photocurrent density of 1.15 mA/cm2 at 0 V (vs. Ag/AgCl), corresponding to a photoconversion efficiency of 0.70%, which was superior to Ni-doped and Si-doped TiO2. This improvement in PEC water splitting could be attributed to the extended light absorption, faster charge transfer, possibly lower charge recombination, and longer lifetime.
Ti-Ni-Si-O nanostructures were successfully prepared on Ti-1Ni-5Si alloy foils via electrochemical anodization in ethylene glycol/glycerol solutions containing a small amount of water. The Ti-Ni-Si-O nanostructures were characterized by field-emission scanning electron microscopy (FE-SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), and diffuse reflectance absorption spectra. Furthermore, the photoelectrochemical water splitting properties of the Ti-Ni-Si-O nanostructure films were investigated. It was found that, after anodization, three different kinds of Ti-Ni-Si-O nanostructures formed in the α-Ti phase region, Ti2Ni phase region, and Ti5Si3 phase region of the alloy surface. Both the anatase and rutile phases of Ti-Ni-Si-O oxide appeared after annealing at 500 °C for 2 h. The photocurrent density obtained from the Ti-Ni-Si-O nanostructure photoanodes was 0.45 mA/cm2 at 0 V (vs. Ag/AgCl) in 1 M KOH solution. The above findings make it feasible to further explore excellent photoelectrochemical properties of the nanostructure-modified surface of Ti-Ni-Si ternary alloys.
4 January 2020 in Journal of the Electrochemical Society
Ni/Si-doped TiO 2 nanostructures were prepared by anodizing Ti-1Ni-5Si alloy. The electrochemical reduction in the aqueous solutions was a simple and effective method to self-dope Ti 3+ into Ni/Si-doped TiO 2 nanostructures. It was found that electrochemical reduction in neutral aqueous solution (pH 7) was more effective than that in either acidic aqueous solution (pH 3) and basic aqueous solution (pH 13). The stable reduced Ni/Si-doped TiO 2 photoanode obtained in the neutral aqueous solution exhibited an excellent photoelectrochemical water splitting performance due to the increased Ti 3+ and oxygen vacancies species, which not only extended the visible-light absorption range but also promoted the charge transfer and separation process. A remarkable photocurrent density of 2.41 mA cm −2 at 0 V vs Ag/AgCl was achieved, corresponding to a photoconversion efficiency of 1.12%, which was 5.9 times that of the undoped TiO 2 photoanode (0.19%).
Ti-Ni-Si-O nanostructures were synthesized on Ti10Ni5Si alloy through an electrochemical anodization in electrolyte solutions containing ammonium fluoride (NH4F). The anodic oxide structures were affected by the electrochemical anodization parameters, including the electrolyte viscosity, water content, anodization potential and anodization time. Using an anodization potential of 40 V for 90 min in an ethylene glycol/glycerol electrolyte with 3 vol.% deionized water, highly ordered self-organized nanotube arrays were obtained in the α-Ti phase region of the alloy substrate, with an average inner diameter of 70 nm and a wall thickness of about 12 nm. Self-organized nanopore structures with an average pore diameter of 25 nm grew in the Ti5Si3 phase region. Only etching pits were found in the Ti2Ni phase region. The Ti-Ni-Si-O nanostructures were characterized using scanning electron microscopy and energy dispersive spectroscopy. In addition, a formation mechanism of different nanostructures was presented.