The size effect has a significant effect on the mechanical behavior of rock, thereby fundamentally influencing the stability of rock excavations. The main challenge associated with the experimental research on the size effect of fractured rock mass lies in the difficulty of specimen preparation to represent the influence of size and fracture on the mechanical behavior of the rock material. In order to preliminarily explore the feasibility of 3D printing technology in the field of rock mechanics, fractured rock specimens of different sizes and different fracture characteristics were produced using sand powder 3D printing technology. The uniaxial compression test was combined with the digital image correlation method (DIC) technology to study the influence of the size effect on the mechanical properties and deformation and failure of different fractured specimens. The research finds that: (1) The elastoplastic mechanical characteristics of the sand powder 3D printed specimens are similar to soft rock. Specimen size and fracture angle have significant effects on the mechanical properties of specimens. Under different fracture conditions, the uniaxial compressive strength (UCS) and Elasticity Modulus of sand powder 3D specimens should be decreased with the increase of the specimen size, and the size effect has different influences on the specimens with different fracture characteristics. (2) Under different fracture conditions, the crack initiation position and failure mode of specimens of various sizes are affected by the fracture inclination to varying degrees. (3) The size effect of fractured rock mass is closely related to the defect level inside the rock mass. The size effect originates from the heterogeneity inside the material. The research results verify the feasibility of applying sand powder 3D printing technology to study the size effect of fractured rock masses and provide an innovative test method for the size effect test study. Preliminary exploration of the size effect of fractured rock masses provides a powerful reference for related research in this field. The study proves the feasibility of applying sand powder 3D printing technology in similar rock mechanics tests and contributes to understanding the size effect of a fractured rock mass.
Numerical testing is an ideal testing method in the research on the mechanical behaviors of jointed rock. However, there are few systematic studies focused on the comparison between the two-dimensional (2D) and the three-dimensional (3D) simulation effects on rock mechanical behaviors, particularly those of jointed rock. In this paper, a particle flow model was established by utilizing PFC2D and PFC3D to represent the rock materials, and the rock (especially jointed rock) mechanical behaviors (uniaxial compressive strength UCS, tensile strength TS, crack initiation stress level Kσ, and the pattern of crack initiation) between 2D and 3D models were compared and analyzed. As expected, the result shows that the UCS and TS showed an increasing tendency with the increase in the joint angle (β) for both the 2D and the 3D models, and the strength of the 3D model was less than that of the 2D model under uniaxial compression but was greater than that of the 2D model under uniaxial tension. The crack initiation and Kσ of the specimens were essentially the same for the 2D and 3D models, and the tensile stresses are more concentrated than the compressive stresses before the failure of the specimen; the uniaxial tensile failure more closely approached abrupt failure than the uniaxial compression failure. The tensile cracks were often initiated at the tips of the joints for both the 2D and 3D models, but they were initiated in the middle of the joints when β was low (β = 0° and β = 15° in both the 2D and 3D models) under uniaxial compression and when β reached 90° under uniaxial tensile. The test results were validated and further analyzed with mathematical analysis. This study has relative referential value to experiments on jointed rock and to analysis of the instability fractures of engineering rock mass.
The random distribution of a complex joint network within a coal–rock mass has a significant weakening effect on its bearing capacity, making the surrounding rock of the roadway highly susceptible to instability and failure under the influence of in situ stress and mining-induced stress. This poses challenges in controlling the surrounding rock and seriously affects the normal production of mines. Consequently, it is imperative to conduct stability analysis on complex jointed roadway surrounding rock. Therefore, taking the transport roadway of Panel 11030 in the Zhaogu No. 2 Coal Mine as a case study, the microscopic contact parameters of particles and joint surfaces in each rock layer were calibrated through uniaxial compression and shear simulation tests using the particle flow simulation software PFC2D 5.0. Based on the calibrated microscopic contact parameters, a multilayered roadway surrounding rock model containing complex joints was established, and the joint density was quantified to analyze its effects on the displacement field, stress field, force chain field, and energy field of the roadway surrounding rock. The research findings indicate that as the distance to the sidewall decreases, the impact of joint density on the deformation of the surrounding rock of the roadway increases. The displacement of the roadway roof, floor, and sidewalls is affected differently by the joint density, predominantly contingent upon the properties of the rock mass. During the process of stress redistribution in the surrounding rock, the vertical stress of the roof and floor is released more intensively compared to the horizontal stress, while the horizontal stress of the sidewalls is released more intensively compared to the vertical stress. The increase in joint density leads to an increasing release rate of the surrounding rock stress, causing the load-bearing rock mass to transfer towards the deeper part. As the joint density increases, the force chain network gradually transitions from dense to sparse, resulting in a decrease in strong force chains and a decline in the bearing capacity of the surrounding rock, accompanied by an expansion in the range of force chain failure and deformation. With the continuous increase in joint density, the values of maximum released kinetic energy and residual released kinetic energy become larger. Once the joint density reaches a certain threshold, the kinetic energy stability zone consistently maintains a high energy level, indicating extreme instability in the roadway and sustained deformation. The results provide a valuable insight for analyzing the failure mechanism of complex jointed roadway surrounding rock and implementing corresponding support measures.
25 July 2021 in Geotechnical and Geological Engineering