In this review, the use of x-ray computed tomography (XCT) is examined, identifying the requirement for volumetric dimensional measurements in industrial verification of additively manufactured (AM) parts. The XCT technology and AM processes are summarised, and their historical use is documented. The use of XCT and AM as tools for medical reverse engineering is discussed, and the transition of XCT from a tool used solely for imaging to a vital metrological instrument is documented. The current states of the combined technologies are then examined in detail, separated into porosity measurements and general dimensional measurements. In the conclusions of this review, the limitation of resolution on improvement of porosity measurements and the lack of research regarding the measurement of surface texture are identified as the primary barriers to ongoing adoption of XCT in AM. The limitations of both AM and XCT regarding slow speeds and high costs, when compared to other manufacturing and measurement techniques, are also noted as general barriers to continued adoption of XCT and AM.

Selective laser melting (SLM) of metals produces surface topographies that are challenging to measure. Multiple areal surface topography measurement technologies are available, which allow reconstruction of information rich, three-dimensional digital surface models. However, the capability of such technologies to capture intricate topographic details of SLM parts has not yet been investigated. This work explores the topography of a SLM Ti6Al4V part, as reconstructed from measurements by various optical and non-optical technologies. Discrepancies in the reconstruction of local topographic features are investigated through alignment and quantitative assessment of local differences. ISO 25178-2 areal texture parameters are computed as further comparison indicators

The challenges of measuring the surface topography of metallic surfaces produced by additive manufacturing are investigated. The differences between measurements made using various optical and non-optical technologies, including confocal and focus-variation microscopy, coherence scanning interferometry and x-ray computed tomography, are examined. As opposed to concentrating on differences which may arise through computing surface texture parameters from measured topography datasets, a comparative analysis is performed focussing on investigation of the quality of the topographic reconstruction of a series of surface features. The investigation is carried out by considering the typical surface features of a metal powder-bed fusion process: weld tracks, weld ripples, attached particles and surface recesses. Results show that no single measurement technology provides a completely reliable rendition of the topographic features that characterise the metal powder-bed fusion process. However, through analysis of measurement discrepancies, light can be shed on where instruments are more susceptible to error, and why differences between measurements occur. The results presented in this work increase the understanding of the behaviour and performance of areal topography measurement, and thus promote the development of improved surface characterisation pipelines.

In this paper, we will review the development and use of an ISO standardised framework to allow calibration of surface topography measuring instruments. We will draw on previous work to present the state of the art in the field in terms of employed methods for calibration and uncertainty estimation based on a fixed set of metrological characteristics. The resulting standards will define the metrological characteristics and present default methods and material measures for their determination—the paper will summarise this work and point out areas where there is still some work to do. An example uncertainty estimation is given for an optical topography measuring instrument, where the effect of topography fidelity is considered.

Surface topography measurement for metal additive manufacturing (AM) is a challenging task for contact and noncontact methods. We present an experimental investigation of the use of coherence scanning interferometry (CSI) for measuring AM surfaces. Our approach takes advantage of recent technical enhancements in CSI, including high dynamic range for light level and adjustable data acquisition rates for noise reduction. The investigation covers several typical metal AM surfaces made from different materials and AM processes. Recommendations for measurement optimization balance three aspects: data coverage, measurement area, and measurement time. This study also presents insight into areas of interest for future rigorous examination, such as measuring noise and further development of guidelines for measuring metal AM surfaces.

The use of state-of-the-art areal topography measurement instrumentation allows for a high level of detail in the acquisition of topographic information at micrometric scales. The 3D geometric models of surface topography obtained from measured data create new opportunities for the investigation of manufacturing processes through characterisation of the surfaces of manufactured parts. Conventional methods for quantitative assessment of topography usually only involve the computation of texture parameters, summary indicators of topography-related characteristics that are computed over the investigated area. However, further useful information may be obtained through characterisation of signature topographic formations, as more direct indicators of manufacturing process behaviour and performance. In this work, laser powder bed fusion of metals is considered. An original algorithmic method is proposed to isolate relevant topographic formations and to quantify their dimensional and geometric properties, using areal topography data acquired by state-of-the-art areal topography measurement instrumentation.