Julíe Lévesque

Dr. Julíe Lévesque

Québec Metallurgy Center, Leader of the Metal Forming and Assembly Group, 3095 Westinghouse, Trois-Rivières, QC, Canada
orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 September 2023 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
TOThéo Ouellet
Théo Ouellet
MCMaxime Croteau
Maxime Croteau
ABAlexandre Bois-Brochu
Alexandre Bois-Brochu
JLJulíe Lévesque
Julíe Lévesque
Additive manufacturing is used to produce parts with complex near-net shape geometries. It can also be used to repair parts that have worn out in service using specific processes such as Wire Arc Additive Manufacturing (WAAM) and Directed Energy Deposition (DED). Wire additive manufacturing processes allow for relatively high deposition rates compared to powder technologies but necessitate a stable welding process and a controlled heat input. As the perfect transfer mode for low welding energy and low spatter, Cold Metal Transfer (CMT) is the process of choice for WAAM. In this project, parts made from aluminium 4943 and 6061 were additively manufactured using CMT technology. The deposition rate, porosity level, and mechanical properties are discussed herein. For the 6061 alloy, after heat treatment, it is possible to attain properties that are close to those obtained for T6 for wrought products or even higher when samples are hot-isostatically pressed.

13 September 2023 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
MKMohammad Khoshghadam-Pireyousefan
Mohammad Khoshghadam-Pireyousefan
Mousa JavidaniMousa Javidani
Mousa Javidani
AMAlexandre Maltais
Alexandre Maltais
JLJulíe Lévesque
Julíe Lévesque
XCX.-Grant Chen
X.-Grant Chen
This study investigated the effects of annealing on the microstructure, mechanical properties, and electrical conductivity (EC) of AA4043 rods produced through the Properzi CCR process. Annealing was conducted at two temperatures (200 °C and 300 °C) for 4 h. Characterization techniques were performed on the rod samples, including optical microscopy, EBSD, microhardness, tensile tests, and EC measurements. The results showed a significant improvement in EC with decreased mechanical strength during annealing. The sample annealed at 300 °C exhibited the most favorable combination of EC (57.48% IACS), microhardness (41 HV), and ultimate tensile strength (124 MPa). Furthermore, the image analysis revealed slight alterations in the shape factors of eutectic Si particles with increasing annealing temperature. In addition, EBSD results demonstrated that the annealing promoted the recrystallization process.


6 January 2023
Verified
Book Chapter
Closed access
PDF file
JLJulíe Lévesque
Julíe Lévesque
ABAlexandra Béland
Alexandra Béland

16 June 2025
Verified
Book Chapter
Open access
PDF file
WJWalid Jomaa
Walid Jomaa
KBKadiata Ba
Kadiata Ba
JLJulíe Lévesque
Julíe Lévesque
AGAugustin Gakwaya
Augustin Gakwaya
This paper proposes a comprehensive analysis of the evolution of the surface residual stress state over the manufacturing stages of generic forged aircraft components. This has been achieved through an experimental procedure, involving forging of the generic component preforms, heat treatments, and machining operations on Computer Numerical Control milling and lathe centers. Surface residual stresses were measured using X-ray diffraction technique. The results showed a high scatter of surface residual stress measured in the same zone although the machining was done by the same cutting tool and under the same machining conditions. This suggests that the residual stress measured at a specific zone is significantly sensitive to previous and further major material removal such as rough pocketing the components have underwent. Moreover, it was found that the quenching and aging heat treatment drastically modify, not only the machining induced-residual stress state, but also the physical surface characteristics as demonstrated by the shear to normal residual stress ratio and the full width at half maximum of the X-ray diffraction peaks. Conclusively, the findings of this work help both researchers and manufacturers to better understand the challenges related to the design and the manufacturing of structural aircraft components made from forgings.