We investigate the anomalous Hall effect in a van der Waals material Fe5GeTe2. We find a distinct difference in the temperature dependence of the anomalous Hall effect associated with the evolution of magnetic states in Fe5GeTe2 films. In the low-temperature region, the anomalous Hall conductivity changes with the longitudinal conductivity, which highlights the substantial contribution from the extrinsic mechanism. The extracted skew scattering coefficient in the Fe5GeTe2 films is an order of magnitude larger than that in transition metal ferromagnets. This result sheds light on the role of the extrinsic mechanism in the anomalous Hall effect in van der Waals magnets.
We investigate the impact of crystallinity on the generation of orbital torques in Ni, which is predicted to exhibit the strongest orbital response among conventional ferromagnetic metals. We show that the current-induced torques in Hf/Ni bilayers are primarily dominated by the orbital torque, arising from the orbital Hall effect in the Hf layer. We find that the orbital torque efficiency is enhanced by a factor of 2 when the stacking order of the Hf/Ni bilayer is altered. Through the examination of bulk and interfacial structural properties of the Ni and Hf layers, and by quantifying the torque efficiency in a symmetric Hf/Ni/Hf trilayer, we show that the orbital torque efficiency is strongly dependent on the crystallinity of the Ni layer. This dependence is in stark contrast to conventional spin-orbit torques, which arise from the spin Hall effect and are typically insensitive to the crystallinity of the ferromagnetic layer. These findings highlight the significant role of the crystalline structure of the ferromagnetic layer in its orbital response and illustrate the potential of crystal structure engineering in optimizing orbital torques.
Hard coatings, such as transition metal nitrides, have been widely applied to improve the mechanical properties and tribological performance of cutting tools. The coatings in various multilayered or gradient structures have been designed to meet the demands of more severe service environments and more precise processing requirements. In this work, TiN/TiSiN coatings in several gradient and multilayered structures were deposited on cemented carbides by cathodic arc ion plating using Ti and TiSi alloy targets. The modulation period (Λ) of the multilayer gradually varies with thickness, ranging from 6 to 46 nm. The gradient multilayer coatings consist of a nanocrystalline-amorphous composite with compact growth. The coating with a modulation period first increasing and then decreasing has the highest hardness of 38 GPa, and the maximum residual compressive stress of −2.71 GPa, as well as the minimum coefficient of friction (COF) and wear rate. Gradient and multilayer structures moderate the brittleness caused by the presence of amorphous SiNx phase and optimize the mechanical properties and tribological performances of the coatings.
29 July 2024 in Journal of Vacuum Science & Technology A
The structure design and optimization of multilayer coatings, which are utilized to surmount the trade-off between hardness and toughness, has been a current hot topic in the field of hard ceramic coatings. Herein, multi-layered TiSiN/AlCrN coatings with a constant and gradient sublayer thickness (Λ, modulation periods) ranging from 20 to 3.8 nm were prepared by the cathodic arc ion plating. The microstructure, mechanical properties, residual stress, and fracture toughness of four gradient structures were investigated systematically. All coatings exhibit a typical FCC crystal structure. In the coating with a monotonous decrease of modulation period (single gradient periodic decreasing structure, G2), the interface between the TiSiN layer and the AlCrN layer transformed from a partially semi-coherent interface at the bottom layers of Λ = 20 nm, to a fully coherent interface at the top layers of Λ = 3.8 nm. The coating with dual-gradient structures (modulation period increases first and then decreases, V2) demonstrated the highest hardness (37.6 ± 1.0 GPa), H/E* and H3/E*2 ratios (0.087 and 0.28 GPa), and bonding strength (75.3 N), as well as lowest friction coefficient (0.34) and wear rate (6.7 × 10−6 mm3/N m). The remarkable resistance to damage and toughness displayed by the V2 structure could be ascribed to its intrinsic capacity for effectively alleviating stress concentration and accommodating incompatibilities during the plastic deformation process. This work offers insights into employing gradient architecture design to enhance the strength and toughness of coatings.
The large-scale application of stainless steel (SS) bipolar plates (BPs) in proton exchange membrane fuel cells (PEMFCs) is mainly limited by insufficient corrosion resistance and electrical conductivity. In this work, Ta-Nb-N coatings were prepared on 316L SS substrates by unbalanced magnetron sputtering to improve corrosion resistance and conductivity. The Ta-Nb-N coatings had a dense structure without obvious defects. In simulated PEMFC cathode environments consisting of 0.5 M H2SO4 + 2 ppm HF at 70 ± 0.5 °C, which is harsher than the U.S. Department of Energy specification, the corrosion current density of Ta-Nb-N-coated BPs was reduced to 2.2 × 10−2 Acm−2. Ta-Nb-N-coated samples showed better electrical conductivity than 316L SS, which had an excellent interfacial contact resistance of 9.2 mΩcm2. In addition, the Ta-Nb-N-coated samples had a water contact angle of 100.7°, showing good hydrophobicity for water management. These results indicate that Ta-Nb-N coatings could be a promising material for BPs.