Nowadays, wireless power transfer (WPT) has attracted great attention from researchers because it is a safe, convenient, and reliable way to recharge electric vehicles. Square and circular coils are most commonly used in WPT systems. However, there are few analyses of comparing these two geometry windings in detail. In this paper, two analytical models of both square and circular planar spiral coils between two semi-infinite substrates are developed based on Fourier-Bessel transformation and dual Fourier transformation. An analytical calculation of the selfand mutual inductance can be carried out with respect to the main parameters of the WPT systems such as the line spacing, the number of turns of the coils and the properties of the substrate. The analytical models can be used to investigate the different tendencies of selfand mutual inductance of square and circular coils, which is helpful for speeding up the design process. Finally, to compare the lateral misalignment tolerance between square and circular coils, a 600 mm × 600 mm with a nominal 200-mm-gap prototype has been built and tested.
1 March 2022 in IEEE Transactions on Industrial Electronics
In this article, a self-tuning LCC/LCC wireless power transfer system based on switch-controlled capacitors is proposed to maintain a high power factor on the primary inverter side and fixed output power on the secondary side against self or mutual inductance variation of the magnetic coupler. The PI control on the primary side and the method of gradient descent on the secondary side are proposed based on the proposed normalized mistuned LCC/LCC circuit model. Only two switch-controlled capacitors on each primary and secondary side are used to implement the control scheme without the Wi-Fi communication or parameter identification. A 3 kW experiment setup was built in the lab and two different magnetic shields, namely ferrite and nanocrystalline, were tested on the secondary pad. According to the experiment results, the proposed system is proven to be able to maintain a high power factor (>0.9) and the desired dc output power against 52% mutual inductance variation and 12% self-inductance variation of the secondary pad. The proposed system can be applied as a wireless charger for electric vehicles or a high-power wireless charger test bench.
18 August 2020 in IEEE Transactions on Industrial Electronics
The ferrite core plays an essential role in coupling enhancement and magnetic shielding for the wireless power transfer of electric vehicles. However, ferrite has apparent defects, such as a low saturation and brittleness, especially at the vehicle side. Therefore, a novel flexible nanocrystalline core is proposed in this article, which has high flexibility and high saturation limits. However, the nanocrystalline core has a large eddy current under 85-kHz excitation, so the refinement crushing process and alternating seamless stitching process are adopted to reduce the eddy loss. The feasibility of the improvement process is preliminarily verified via finite element simulations, and four nanocrystalline cores with different permeabilities are obtained. Through static parameter measurements and 7.7-kW loading tests, the modified nanocrystalline cores achieve excellent results. Based on the above, the nanocrystalline core with the best performance is further selected for an anti-saturation test and leakage measurement at 11 kW. Even when the thickness is reduced to 2 mm, the ac–ac efficiency remains 97.408%. The maximum core temperature is only 80.9 °C, and the flux leakage completely satisfies the limit requirements of ICNIRP 2010. In contrast, the ferrite core cannot withstand the impact of a strong alternating field and fails.
9 October 2020 in IEEE Transactions on Power Electronics
This paper proposes a multi-objective optimization method of a primary double-D pad for Inductive Power Transfer (IPT) systems. First, a parametric sweep analysis is conducted to choose the crucial design parameters. Then, using the non-dominated sorting genetic algorithm II (NSGA-II), the structure of the double-D pad can be optimized based on two key objectives; ensuring a good coupling coefficient while minimizing the worst-case stray leakage magnetic fields. Several useful design guidelines are found from the optimization results, including how the dimensions of both the coil and layers affect the coupling coefficient and stray leakage magnetic fields around the pad. A practical coil suitable for wireless charging of electric vehicles at level 2, similar to that recommended in SAE J2954, is used as the reference and also as the starting point for the optimization. Two of the coil structures resulting from the optimization are chosen and investigated further to assess their performance with different secondary pad misalignments using finite element methods. Finally, an experimental setup is built to validate the optimal pad structures.
18 December 2023 in IEEE Transactions on Power Electronics
Fe-based nanocrystalline ribbon is an alternative to the ferrite for high-frequency magnetic cores due to its low hysteresis loss and high magnetic saturation. The drawback of the Fe-based nanocrystalline ribbon is its high conductivity. Crushing the homogenous ribbon to restructure a nanocrystalline flake ribbon (NFR) can reduce the conductivity while maintaining other superior magnetic properties of the noncrushed nanocrystalline ribbon. So far, several previous works have proven that the NFR can replace the ferrite in the dual active bridge and wireless power transfer system. However, seldom of these works mention the detailed mechanism of the NFR. In this article, the structure and manufacturing process of the NFR are introduced. The effect of the relative permeability and the crushing pattern on the magnetic properties of NFR has been quantitatively reported. A dual-permeability core formed by two types of NFR has been demonstrated for an inductor. Comparison has been made to inductors using the ferrite core (N27, N87, DMR44) in a similar size. Experiment results show that the dual-permeability NFR core has a lower core loss and higher magnetic saturation than the ferrite counterparts at frequencies from 100 to 300 kHz.
11 July 2022 in IEEE Transactions on Power Electronics
This letter reports characterization of the novel nanocrystalline flake ribbon (NFR) soft magnetic material. The comparative analysis among the ferrite N87, N27, and the NFR is presented at different temperature, frequency, and peak magnetic flux density, respectively. Experimental results prove that the NFR has lower loss density, higher magnetic flux density saturation, and better temperature stability from 85 to 300 kHz. A LCL resonant tank based circuit is employed for large signal characterization. The mass-based stacking factor of the NFR core is adopted to describe the core structure. This letter suggests that the NFR is a good alternative to the ferrite for high power magnetic cores due to its superior performance and flexibility structures.