Song Wang

Dr. Song Wang


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 January 2024 in Electronics
Verified
Journal Article
Open access
PDF file
QZQinghua Zeng
Qinghua Zeng
ZCZhengtian Chen
Zhengtian Chen
MHMengyun He
Mengyun He
SWSong Wang
Song Wang
XLXiao Liu
Xiao Liu
Haitao XuHaitao Xu
Haitao Xu
The central element of a phased array antenna that performs beam electrical scanning, as well as signal transmission and reception, is the transceiver (T/R) module. Higher standards have been set for the integration, volume, power consumption, stability, and environmental adaptability of T/R modules due to the increased operating frequency of phased array antennas, the variability of application platforms, and the diversified development of system functions. Device-based multichannel T/R modules are the key to realizing low-profile Ka-band phased array antenna microsystem architecture. The design and implementation of a low-profile, high-performance, and highly integrated Ka-band phased array antenna T/R module are examined in this paper. Additionally, a dependable Ka-band four-channel T/R module based on Si/GaAs/Low Temperature Co-fired Ceramic (LTCC), applying multi-material heterogeneous integration architecture, is proposed and fabricated. The chip architecture, transceiver link, LTCC substrates, interconnect interface, and packaging are all taken into consideration when designing the T/R module. When compared to a standard phased array antenna, the module’s profile shrunk from 40 mm to 8 mm, and its overall dimensions are only 10.8 mm × 10 mm × 3 mm. It weighs 1 g, and with the same specs, the single channel volume was reduced by 95%. The T/R module has an output power of ≥26 dBm for single-channel transmission, an efficiency of ≥25%, and a noise factor of ≤4.4 dB. When compared to T/R modules based on System-on-Chip (SOC) devices, the RF performance has significantly improved, as seen by an increase in single channel output power and a decrease in the receiving noise factor. This work lays a foundation for the devitalization and engineering application of T/R modules in highly reliable application scenarios.

17 October 2023 in Materials
Verified
Journal Article
Open access
PDF file
SWSong Wang
Song Wang
THTianyu Hou
Tianyu Hou
RHRui Huo
Rui Huo
ZCZhengtian Chen
Zhengtian Chen
QZQinghua Zeng
Qinghua Zeng
XLXiao Liu
Xiao Liu
A microwave transmitter/receiver using the low-temperature co-fired ceramic substrate and ball grid array packaging demonstrates superior properties, including high integration, miniaturization, and high electromagnetic shielding. However, it holds limitations of inadequate hermeticity (that is, gas or moist impermeability), high cost, and low reproducibility. In this work, we aim to overcome these difficulties by introducing a new packing technique. The packaging utilizes an electroless plated Ni/Pd/Au surface, resulting in a significant enhancement of the packaging hermeticity by orders of magnitude, approaching the level of <5 × 10−9 Pa·m3/s. Both Sn63Pb37 and Au80Sn20 solder alloys demonstrate exceptional solderability, attributed to Pd atoms diffusing to the Au layer during soldering at 310 °C. A reliability test of the packaging shows that the shear strength of the solder balls drops after thermal shocks but negligibly affects the hermeticity of the packaging. Furthermore, a meticulously designed internal vertical interconnect structure and I/O interconnections were engineered in the ball grid array packaging, showcasing excellent transmission characteristics within the 10–40 GHz frequency range while ensuring effective isolation between ports.

6 April 2023 in Crystals
Verified
Journal Article
Open access
PDF file
SWSong Wang
Song Wang
GSGe Shi
Ge Shi
LZLibo Zhao
Libo Zhao
Yanwei DaiYanwei Dai
Yanwei Dai
THTianyu Hou
Tianyu Hou
Fei QinFei Qin
Fei Qin
Due to its higher energy and smaller heating area, laser joining technology is widely used in aluminum alloy welding and other industrial fields, which meets the solder sealing requirements for electronic packaging. According to experiments, cracks were prone to occur at the corners and spot-welding positions near the weld. In this paper, the depth and width of the melt pool were measured experimentally, and the results were used to calibrate and validate the heat source model. An empirical relationship between heat source parameters and melt pool morphology is presented. The heat source model of laser deep penetration welding was established under the same experimental conditions. And the results were in agreement with the experimental results. The finite element method was used to numerically simulate the welding process of a 50%SiAl shell and a 27%SiAl cover plate. The effects of different spot-welding sequences and numbers on the residual stress and cracking possibility of laser welded samples were analyzed. The results show that under sequential spot-welding, when the amount of spot-welding is increased, the stress peak value decreases. Compared with sequential spot welding and side-by-side spot welding, the spot-welding sequence of diagonal points first, and then side-by-side spot welding, can effectively reduce the residual stress. This research enables us to provide some guidelines in terms of studying the reliability issues of microwave devices.

12 March 2026 in Electronics
Verified
Journal Article
Open access
PDF file
MHMengyun He
Mengyun He
QZQinghua Zeng
Qinghua Zeng
XZXuesong Zhao
Xuesong Zhao
SWSong Wang
Song Wang
YZYan Zhao
Yan Zhao
XLXiao Liu
Xiao Liu
Based on monolithic microwave integrated circuit (MMIC) technology, this paper presents the design and implementation of a low-cost, highly integrated Ka-band sixteen-channel transmit/receive (T/R) module, specifically tailored to meet the application requirements of phased array antennas in airborne and spaceborne radar systems, satellite communications, and 5G/6G millimeter-wave networks. The proposed module employs an MMIC-based single-channel dual-chip discrete architecture, optimally integrating amplitude-phase multifunction chips and transmit-receive multifunction chips in terms of both fabrication process and performance characteristics, achieving a favorable balance between high performance and high-integration density. Using low-cost, low-temperature co-fired ceramic (LTCC) substrates, full-silver conductive paste, and a nickel–palladium–gold plating process, a novel “back-to-back” thin-slice packaging technique is presented to improve integration, lower manufacturing costs, and boost long-term reliability. Furthermore, the design incorporates glass insulators and a direct array interconnection scheme, which significantly minimizes transmission losses and reduces interface dimensions. The final module measures 70.3 mm × 26.2 mm × 10.9 mm and weighs only 34 g. Experimental results demonstrate a transmit output power of at least 23 dBm, a receive gain exceeding 26 dB, and a noise figure below 3.5 dB, achieving a 22.5–58% reduction in volume per channel while maintaining competitive RF performance. To improve testing effectiveness and guarantee data consistency, an automated radio frequency (RF) test system based on Python 3.11.5 was also developed. This work provides a practical technical approach for the engineering realization of Ka-band phased array systems.