Variations in vegetation indices derived from multispectral images and digital terrain models from satellite imagery have been successfully used for reclamation and hazard management in former mining areas. However, low spatial resolution and the lack of sufficiently detailed information on surface morphology have restricted such studies to large sites. This study investigates the application of small, unmanned aerial vehicles (UAVs) equipped with multispectral sensors for land cover classification and vegetation monitoring. The application of UAVs bridges the gap between large-scale satellite remote sensing techniques and terrestrial surveys. Photogrammetric terrain models and orthoimages (RGB and multispectral) obtained from repeated mapping flights between November 2023 and May 2024 were combined with an ALS-based reference terrain model for object-based image classification. The collected data enabled differentiation between natural forests and areas affected by former mining activities, as well as the identification of variations in vegetation density and growth rates on former mining areas. The results confirm that small UAVs provide a versatile and efficient platform for classifying and monitoring mining areas and forested landslides.
The limited accessibility during visual inspections remains a central problem for maintaining and repairing of landslide drainage structures. Unwanted mineralization processes cause clogging and damage to drainage pipes, leaving reconstruction as the only option for remediation. Studies of water wells and tunnel drainages have shown that hydrochemical inspections can efficiently detect chemically triggered clogging processes at an early stage. However, these processes have barely been recognized in landslide drainages. Three drainage structures from sites with varying traffic intensity were selected from the road network in south-eastern Austria. Drainage waters and mineral scalings were analyzed to assess the hydrochemical conditions causing unwanted clogging processes. All sites exhibited unexpectedly high electrical conductivity values reaching up to 2500 μS/cm compared to the natural environmental background of ∼400-600 μS/cm, due to the application of road salt during the winter season. The resulting high Na+ concentrations (up to 300 mg/L) triggered Ca2+ exchange reactions within the soil and leaching of concrete elements, which both favored the formation of Ca-carbonate (CaCO3) deposits of up to ∼1500 kg and the neoformation of ∼12 kg of kaolinitic clay per year within the drainage systems. Based on these results, a concept for the integration of hydrochemical methods during drainage inspections was developed, allowing the identification of problematic sites and mitigation measures at an early stage.
InSARTrac is an innovative method for 3D displacement monitoring that combines terrestrial interferometric synthetic aperture radar (InSAR) and computer vision-based feature tracking. The 3D measurements obtained are considered far superior to 1D or 2D data and facilitate evaluations concerning the mechanisms controlling kinematics. This study presents the results of InSARTrac measurements at the Mölltal Glacier in Carinthia, Austria. The duration of glacier monitoring was four weeks and involved two instrument setup positions to obtain comparative measurements of supraglacial rock debris from different angles without utilizing retroreflectors. The mean displacement rate of the resultant vector is 22 mm/day and includes ~11 mm/day in the downgradient ice surface direction and 6 to 18 mm/day vertically downward. Additionally, the entire glacier surface was measured three times using a LIDAR-equipped UAV, revealing mean vertical displacements of 16 mm/day. The measurements indicate an InSARTrac accuracy of 4.2 ppm, which is 27% lower than in the initial controlled tests utilizing retroreflectors. The field test demonstrates the capability of InSARTrac to provide meaningful 3D displacement measurements of supraglacial rock debris. The material monitored has texture and reflectivity similar to certain classes of landslides, rock glaciers, and other alpine processes, indicating that InSARTrac has promising applications for monitoring a variety of geologic phenomena.
The monitoring of carbon emissions is increasingly becoming a sustainability issue worldwide. Despite being largely unnoticed, the toxic gas carbon monoxide (CO) is ubiquitous in mechanized tunnel driving, but the individual sources, release and enrichment mechanisms are often unknown. In this study, the generation of CO from organic matter containing sedimentary rocks was investigated during mechanized tunnel driving and by reacting claystone and sandstone with 10 mM NaCl solutions for 2 months at 70 °C and 140 °C. The mineralogical and geochemical evolution of the solids and fluids was assessed by CO measurements and the XRD, DTA, TOC, IC and ICP-OES methods. The CO concentration in the atmosphere reached up to 1920 ppm (100 ppm on average) during tunnel driving, which is more than three times higher than the legal daily average dose for tunnellers, thus requiring occupational safety operations. Mineral-specific dissolution processes and the rapid decomposition of labile organic matter upon thermal alteration contributed to the liberation of CO and also carbon dioxide (CO2) from the host rocks. In mechanized tunnel driving, frictional heat and ‘cold’ combustion with temperatures reaching 50–70 °C at the drill head is an important mechanism for increased CO and CO2 generation, especially during drilling in sedimentary rocks containing significant amounts of OM and when the ventilation of the tunnel atmosphere and air mixing are limited. Under such conditions, human health damage due to CO exposure (HHDCO) can be 30 times higher compared to tunnel outlets, where CO is emitted from traffic.
Soft and weak rocks present challenges for construction activities in various environments. Their genetic origin, geological and tectonic evolution, and exposure to atmospheric conditions control their weathering and degradation over time. Therefore, a sound characterization of the associated rock parameters is essential. Numerous tests have been developed and standardized or defined in recommendations to assess various geomechanical, petrological, and mineralogical parameters. However, these tests are still subject to modification or extension to address project-specific issues. Additionally, standardized tests do not consider regional climatic conditions that may affect weathering, meaning they do not reflect the degradation behavior that is observed in the field. The present study investigates the slaking resistance and degradability of a range of soft rocks. The workflow of widely used tests is employed to evaluate their representativeness for different rock types in practical applications. Depending on their genetic origin and mineral composition, fabric alterations affect the rate and style of rock disintegration differently. Soft sedimentary rocks react already to static slaking, i.e., water immersion, whereas crystalline and grain-bound rocks slake under dynamic action while undergoing attrition in a rotating slake durability drum. Zones of structural weakness, such as foliation planes, are responsible for material removal in the latter; sedimentary rocks, on the other hand, are subject to surface particle separation (suspension) and suction due to the presence of clay minerals. This study presents an approach that combines the results of several routine tests to help identify and refine the slaking susceptibility of different rock types. A routine for inspecting and documenting the evaluated slaking characteristics for infrastructure maintenance is proposed, and the wider implications in light of climate change are discussed. Some limitations of the transferability of laboratory values to field sites still have to be evaluated and validated in the future.