Mineral precipitates (scaling) from deep saline thermal waters often constitute a major problem during geothermal energy production. The occurrence of scale-fragments accumulating and clogging pipes, filters, and heat exchangers is of particular concern regarding an efficient energy extraction. Carbonate scale-fragments from different sections of two geothermal power plants were collected and studied in a high-resolution scaling forensic approach comprising of microstructural characterization, elemental mapping, and stable carbon and oxygen isotope transects. The solid-phase analyses were evaluated in the context of natural environmental and technical (man-made) production conditions. Our results indicate an interaction of metal sulfide mineral layers mainly from H2S corrosion of the steel pipes and CaCO3 nucleation and crystal growth. A conceptual model of scale-fragment development addresses the relevance of two key interfaces: 1) the corrosion layer between the steel substrate and calcite scale and 2) the scale surface versus thermal fluid flow. The corrosion products constitute an attractive crystallization substrate of brittle and mechanically weak consistency. A rough carbonate scale surface tends to induce (micro) turbulences and increased flow resistance (frictional forces). These factors promote partial exfoliation, scale-fragment mobilization, and rapid clogging. This investigation highlights the potential of detailed petrographic and geochemical analyses of mineral precipitates for evaluating favorable versus unfavorable processes in geotechnical environmental settings.
The well‐known Erzberg site represents the largest siderite (FeCO3) deposit in the world. It consists of various carbonates accounting for the formation of prominent CaCO3 (dominantly aragonite) precipitates filling vertical fractures of different width (centimetres to decimetres) and length (tens of metres). These commonly laminated precipitates are known as ‘erzbergite’. This study focuses on the growth dynamics and environmental dependencies of these vein fillings. Samples recovered on‐site and from mineral collections were analyzed, and these analyses were further complemented by modern water analyses from different Erzberg sections. Isotopic signatures support meteoric water infiltration and sulphide oxidation as the principal hydrogeochemical mechanism of (Ca, Mg and Fe) carbonate host rock dissolution, mobilization and vein mineralization. Clumped isotope measurements revealed cool formation temperatures of ca 0 to 10°C for the aragonite, i.e. reflecting the elevated altitude Alpine setting, but unexpectedly low for aragonite nucleation. The 238U–234U–230Th dating yielded ages from 285·1 ± 3·9 to 1·03 ± 0·04 kyr bp and all samples collected on‐site formed after the Last Glacial Maximum. The observed CaCO3 polymorphism is primarily controlled by the high aqueous Mg/Ca ratios resulting from dissolution of Mg‐rich host rocks, with Mg/Ca further evolving during prior CaCO3 precipitation and CO2 outgassing in the fissured aquifer. Aragonite represents the ‘normal’ mode of erzbergite formation and most of the calcite is of diagenetic (replacing aragonite) origin. The characteristic lamination (millimetre‐scale) is an original growth feature and mostly associated with the deposition of stained (Fe‐rich) detrital particle layers. Broader zonations (centimetre‐scale) are commonly of diagenetic origin. Petrographic observations and radiometric dating support an irregular nature for most of the layering. Open fractures resulting from fault tectonics or gravitational mass movements provide water flow routes and fresh chemical reaction surfaces of the host rock carbonates and accessory sulphides. If these prerequisites are considered, including the hydrogeochemical mechanism, modern water compositions, young U‐Th ages and calculated precipitation rates, it seems unlikely that the fractures had stayed open over extended time intervals. Therefore, it is most likely that they are geologically young.
The monitoring of carbon emissions is increasingly becoming a sustainability issue worldwide. Despite being largely unnoticed, the toxic gas carbon monoxide (CO) is ubiquitous in mechanized tunnel driving, but the individual sources, release and enrichment mechanisms are often unknown. In this study, the generation of CO from organic matter containing sedimentary rocks was investigated during mechanized tunnel driving and by reacting claystone and sandstone with 10 mM NaCl solutions for 2 months at 70 °C and 140 °C. The mineralogical and geochemical evolution of the solids and fluids was assessed by CO measurements and the XRD, DTA, TOC, IC and ICP-OES methods. The CO concentration in the atmosphere reached up to 1920 ppm (100 ppm on average) during tunnel driving, which is more than three times higher than the legal daily average dose for tunnellers, thus requiring occupational safety operations. Mineral-specific dissolution processes and the rapid decomposition of labile organic matter upon thermal alteration contributed to the liberation of CO and also carbon dioxide (CO2) from the host rocks. In mechanized tunnel driving, frictional heat and ‘cold’ combustion with temperatures reaching 50–70 °C at the drill head is an important mechanism for increased CO and CO2 generation, especially during drilling in sedimentary rocks containing significant amounts of OM and when the ventilation of the tunnel atmosphere and air mixing are limited. Under such conditions, human health damage due to CO exposure (HHDCO) can be 30 times higher compared to tunnel outlets, where CO is emitted from traffic.