Zhao Lin

Dr. Zhao Lin

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 November 2022 in Journal of Thermal Spray Technology
Verified
Journal Article
Closed access
PDF file
YZYu Zhang
Yu Zhang
SSShilong Sun
Shilong Sun
ZLZhao Lin
Zhao Lin
CYChangdi Yang
Changdi Yang
LWLiping Wu
Liping Wu
AAAndrew Siao Ming Ang
Andrew Siao Ming Ang

21 March 2025 in Materials
Verified
Journal Article
Open access
PDF file
MZMiao Zhang
Miao Zhang
YZYu Zhang
Yu Zhang
PDPengyu Dai
Pengyu Dai
ZLZhao Lin
Zhao Lin
LWLiping Wu
Liping Wu
SLShendian Li
Shendian Li
FeCoNiCrAl high-entropy alloy (HEA) coating was prepared by air plasma spraying, and the coating’s morphology and properties under different power parameters were analyzed. The results show that the spraying power significantly affects the morphology of the coating during plasma spraying. The molten droplets formed during the preparation process of HEA coatings tend to combine with oxygen, with aluminum bonding particularly strongly with oxygen, resulting in the presence of aluminum oxide within the coating, while other elements exhibit weaker bonding with oxygen. The optimal spraying power is 12 kW, and coatings prepared at this optimal power exhibit advantages such as low porosity, uniform element distribution, and excellent corrosion resistance. The aluminum in the HEA coating forms a relatively stable compound with oxygen, creating a Cr-depleted and Al-enriched region. This region is less prone to passivation during corrosion and more susceptible to reacting with corrosive media, leading to localized corrosion of the coating.

29 September 2025 in Materials
Verified
Journal Article
Open access
PDF file
JYJiahang Yan
Jiahang Yan
YZYu Zhang
Yu Zhang
PDPengyu Dai
Pengyu Dai
ZLZhao Lin
Zhao Lin
XWXin Wang
Xin Wang
XYXiaohong Yi
Xiaohong Yi
The long-term corrosion behavior of Al2O3-3%TiO2 (AT3) coatings doped with1%, 5% and 8% CeO2 prepared by plasma spraying was studied in 5% NaCl solution. The results showed that the protective performance of CeO2-doped coatings was significantly higher than that of undoped coatings, primarily due to the reduction in coating porosity caused by the addition of rare-earth elements. Among the doped coatings, the 5% CeO2-doped coating exhibited the best protective performance. The addition of rare-earth oxides CeO2 reduced the content of γ-Al2O3 in the coating, but when the concentration of CeO2 increased to 8%, the Ce element was rich in the gap of the coating. Excessive CeO2 enriched in the gaps and coexisted more with Ti, and prevented the formation of the AlTi phase, which affected the performance of the coating. Electrochemical and XPS results revealed that an appropriate amount of Ce atoms or CeO2 particles could fill the pores of the coating. During long-term immersion, Ce (IV) was converted to Ce (III), which demonstrated that Ce atoms have high chemical activity in coatings. The thermodynamic calculation results show that more CeO2 particles improved the adsorption of corrosive ions. It indicated that the content of doped rare-earth oxides exceeding 5% would be utilized as an active material in the corrosive process.

15 December 2023 in Materials Letters
Verified
Journal Article
Closed access
YZYu Zhang
Yu Zhang
SLShendian Li
Shendian Li
SSShilong Sun
Shilong Sun
ZLZhao Lin
Zhao Lin
LWLiping Wu
Liping Wu
AAAndrew Siao Ming Ang
Andrew Siao Ming Ang

15 September 2025 in Crystals
Verified
Journal Article
Open access
PDF file
PDPengyu Dai
Pengyu Dai
YZYu Zhang
Yu Zhang
XWXin Wang
Xin Wang
JYJiahang Yan
Jiahang Yan
ZLZhao Lin
Zhao Lin
XYXiaohong Yi
Xiaohong Yi
Al2O3-3% TiO2-xAl (x = 0, 20, 40, 60 wt.%) composite coatings were prepared on Q235 substrate by plasma spraying technology, and the effects of pure Al phase addition on the microstructure and wear properties of the coatings were compared and analyzed. The results show that a unique splash-like structure was formed on the surface of the coating, and this structure became more obvious with the increase in Al content. Cross-sectional analysis shows that the introduction of pure Al phase reduces the large pores and cracks in the coating, forming a slender band structure. XRD analysis shows that the addition of pure Al phase leads to a decrease in the diffraction peak intensity of α-Al2O3, while the diffraction peak intensity of Al phase and γ-Al2O3 gradually increases, especially in the coating with 40% Al content; the diffraction peak of γ-Al2O3 increases significantly. XPS analysis further confirms that with the increase in Al content, a new pure Al peak appears in the Al element spectrum, and the peaks of α-Al2O3 and γ-Al2O3 fluctuate. In addition, the porosity of the coating decreases first and then increases and then decreases again with the increase in Al content. The porosity of the coating with 60% Al content is the lowest, at only 5.14%. Microhardness test results show that with the increase in Al content, the microhardness of the coating gradually decreases, and the fracture morphology changes from brittle fracture to irregular fracture, with the appearance of pull-out areas, indicating that the pure Al phase effectively improves the brittleness of the coating. However, the friction and wear test results show that the friction coefficient of the coating increases with the increase in Al content. The pure Al2O3 coating has high hardness and excellent wear resistance, while the coating with 60% Al content has the highest friction coefficient and the most severe wear. Moreover, adhesive wear phenomena appear on the coating surface with high Al content.

11 March 2026 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
YYYanzhe Yang
Yanzhe Yang
YZYu Zhang
Yu Zhang
ZLZhao Lin
Zhao Lin
PDPengyu Dai
Pengyu Dai
XYXiaohong Yi
Xiaohong Yi