Edy Purwanto

Mr. Edy Purwanto


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 February 2024 in Buildings
Verified
Journal Article
Open access
PDF file
EPEdy Purwanto
Edy Purwanto
SKStefanus Kristiawan
Stefanus Kristiawan
SSSenot Sangadji
Senot Sangadji
HSHalwan Alfisa Saifullah
Halwan Alfisa Saifullah
Non-engineered buildings (NEBs) are prone to earthquake damage. One type of damage that often occurs in NEBs is the separation of beam and column elements owing to joint failures. Strengthening joints with steel plates is expected to improve the seismic performance of this type of building. Strengthening with steel plates is cheap and easy to apply, so it will be a preferable choice in preventing damage to the NEB due to earthquake loads. This study investigated the seismic performance of reinforced concrete frames, representing an NEB whose beam–column joints were strengthened with L-shaped steel plates. Two widths of L-shaped steel plates were proposed: 75 mm (NEB-075) and 100 mm (NEB-100). An NEB without strengthening (NEB-000) was used as a control. Both experimental and numerical investigations were performed to determine the seismic performance of NEBs. The results showed that damage to the NEB-000 and NEB-075 models occurred at the joints, but less damage was observed in NEB-075 than in NEB-000. Furthermore, damage in the NEB-100 model occurred at the column. The undamaged limit levels of the NEB-000, NEB-075, and NEB-100 models were 56.49, 81.54, and 82.46%, respectively. These results show that strengthening the NEB with steel plates effectively improves its seismic performance. According to an analysis of the performance of the tested models, the NEB-100 model exhibited the best seismic performance.

26 April 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
EPEdy Purwanto
Edy Purwanto
SKStefanus Kristiawan
Stefanus Kristiawan
SSSenot Sangadji
Senot Sangadji
HSHalwan Alfisa Saifullah
Halwan Alfisa Saifullah
Non-compliant (NC) structures are often encountered in building construction in developing countries. This is a condition whereby erected buildings do not follow regulatory standards, especially in the provision of reinforcements. Therefore, under an earthquake load, the structures do not have sufficient resistance against such load. The structural elements of the building, which often have NC conditions, are the beam-column joints because they do not contain adequate shear reinforcements due to installation difficulty. This study aims to determine the structural performance of the reinforced concrete (RC) frame, which has a reinforcement deficiency in the beam-column joints. Numerical simulation was conducted on the Kakaletsis structure model by modifying the reinforcement details at the joints to represent the NC conditions. The non-linear modeling and analysis of the structural model were carried out using ATENA software. The analysis showed that the reduction in shear reinforcements in the NC model joint caused a decrease in load-carrying capacity by about 26.04%. A shift was also observed in the collapse pattern, i.e., from the beam to the end of the column, causing global failure and reducing the undamaged but increasing more severely damaged condition. This showed that the NC structure, due to the non-conformance of reinforcement, significantly reduced the structure's performance.

12 April 2025
Verified
Book Chapter
Closed access
PDF file
EPEdy Purwanto
Edy Purwanto
SKStefanus Adi Kristiawan
Stefanus Adi Kristiawan
HSHalwan Alfisa Saifullah
Halwan Alfisa Saifullah
SSSenot Sangadji
Senot Sangadji
AFAfrizal Aqila Fathin
Afrizal Aqila Fathin
AZAhmad Zaky
Ahmad Zaky

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
EPEdy Purwanto
Edy Purwanto
SKStefanus Kristiawan
Stefanus Kristiawan
SSSenot Sangadji
Senot Sangadji
HSHalwan Alfisa Saifullah
Halwan Alfisa Saifullah
A low concrete compressive strength is a dominant problem in non-engineered buildings because unskilled workers carry out the concrete manufacturing proces A low concrete compressive strength is a dominant problem in non-engineered buildings because unskilled workers carry out the concrete manufacturing proces