Organic dye rhodamine B is one of the common organic pollutants in the water and soil environment. This study investigated the feasibility of removing rhodamine B from an aqueous solution through adsorption by kaolin, kaolin-sodium bentonite, and kaolin-organic bentonite. Batch adsorption test results showed that the maximum adsorption quantities of kaolin, kaolin-sodium bentonite, and kaolin-organic bentonite were 7.76 mg/g, 11.26 mg/g, and 12.68 mg/g, respectively, implying that the addition of bentonite to kaolin can effectively improve its adsorption capacity for rhodamine B. Moreover, the Langmuir isotherm model is suitable to describe the adsorption of rhodamine B by kaolin and kaolin-sodium bentonite, while it is preferable to use the Freundlich isotherm model in the case of kaolin-organic bentonite. The adsorption kinetic characteristics of rhodamine B, by these three adsorbents, are suitable to be described with a pseudo-second order kinetic model. Furthermore, the characteristics of the above three adsorbents were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The above results indicated that kaolin and organic bentonite can be used to design efficient adsorbents for organic pollutants similar to rhodamine B.

Bentonite was modified with cetyltrimethylammonium bromide (CTAB). The organically modified bentonite (OMB) was used to remove phenol from aqueous solution, the microstructural changes were characterized by X-ray diffraction (XRD) and scanning electronic microscopy (SEM), and phenol adsorption kinetic was obtained using batch adsorption test results. The results indicated that the rate of adsorption of phenol onto the OMB was positively correlated with the initial concentration, and the maximum adsorption capacity was found to be 10.1 mg/g at the initial concentration of 150 mg/L at 25 °C and pH 10. The investigations of adsorption kinetics models showed that the adsorption kinetic was better reflected by the pseudo-second-order kinetic model. Furthermore, the properties of the OMB samples with different adsorption times were obtained by SEM and XRD. The statistic analysis revealed that the pore diameter of the OMB samples decreased with the increasing adsorption time and gradually reached equilibrium.

The main objectives of this study were to identify methane hotspots through spatial distribution tests of the surface methane concentration above a landfill final cover and to investigate the effects of rainfall, atmospheric pressure, ground temperature, and ambient methane concentration on methane emissions. A portable laser methane detector was used to measure the spatial distribution of methane concentrations. The methane concentration distribution showed a distinct spatial variability. The maximum methane concentration reached 3225 ppm, while 73.0% of the methane concentration values were below 10.0 ppm. Several meteorological factors were found to be associated with the variation in methane emissions. Rainfall limited gas transport in the cover, resulting in more significant methane hotspots. Atmospheric pressure was negatively correlated with methane emission. The ambient methane concentration and methane flux had a significant positive linear correlation. Based on a linear correlation equation, the spatial distribution of methane concentrations in the landfill could be converted into a methane emission distribution. The estimated average value for methane emissions in the test area was approximately 4.3 g m⁻² d⁻¹. This study provides an experimental basis for locating methane hotspots and assessing methane emissions in landfill final covers, and proposes supplementary means for detecting geomembrane damage in landfill covers.

Capacity expansion of existing landfills is one of the most economical methods of relieving the stress caused by the disposal of local municipal solid waste (MSW) in developing countries. In this paper, the compression characteristics and settlement of the aged MSW in Xiawan landfill were studied. The physical composition, moisture content, volumetric weight, and modified primary compression index of the aged MSW at different depths were tested, and then the settlement of the MSW in the area to be filled with fly ash was calculated. The test results showed that the main components of the aged MSW were muck and textile, indicating that kitchen waste was degraded. The moisture content of the MSW generally increased with depth, and the average moisture content within 5 m of the shallow part of the landfill was 97%. The void ratio of the aged MSW decreased from 4.0 to 2.2 with an increase in vertical load from 1 kPa to 400 kPa. The modified primary compression index of the aged MSW ranged from 0.22 to 0.27, and generally decreased with depth. Under the load generated by the subsequent filling of fly ash, the final strains of the aged MSW was approximately 15% to 20%. The physical composition and compression characteristics of the aged MSW measured in this paper were compared with those reported in previous studies to provide reference for the settlement analysis of landfills with aged MSW.

In this study, the effect of microbead dosages (0%, 5%, 10%, 15%, and 20%) on the carbonation resistance of expanded polystyrene (EPS) concrete was investigated. Five groups of EPS concrete specimens were produced and underwent rapid carbonation testing. The carbonation depth and strength after carbonation of the specimens were measured at different carbonation ages (7 days, 14 days, and 28 days) and analyzed to determine the effect of microbead dosages and compressive strength on carbonation resistance. Results indicated that the carbonation depth increased with the progression of carbonation time. The introduction of microbeads was found to significantly improve the carbonation resistance of EPS concrete, leading to a reduction in carbonation depth of over 50% after 28 days and an increase in strength after carbonation by 18–56%. A relative compressive strength model for EPS concrete after carbonation was developed, which could accurately characterize the growth of compressive strength. Based on the analysis of EPS concrete carbonation depth data, a prediction model for the carbonation depth of EPS concrete with microbead dosage was established through fitting, providing improved accuracy in predicting carbonation resistance. The microstructure of EPS concrete was also examined using scanning electron microscopy to uncover the underlying mechanisms of microbead enhancement on carbonation resistance. These findings have potential implications for future research and engineering applications in the carbonation resistance of EPS concrete.

This study investigated the influence of microbead dosages (0, 5, 10, 15, and 20%) on the frost resistance of expanded polystyrene (EPS) concrete. Five groups of EPS concrete specimens were prepared and subjected to rapid freeze–thaw tests. The freeze–thaw deterioration of EPS concrete was assessed using macroscopic indicators, including mass loss, strength loss, and dynamic elastic modulus loss. The underlying deterioration mechanism was revealed through the analysis of the EPS particle–matrix interface. A concrete damage plasticity model of EPS concrete based on damage mechanics theory was established. The results indicate that the addition of microbeads increased the strength of EPS concrete by 38–53%, reduced the strength attenuation after freeze–thaw damage by 8.1%, and improved the frost resistance level by 10–60 grades. The optimal dosage of microbeads is 15% of the cementitious material. The interfacial transition zone gaps in EPS concrete with added microbeads after freeze–thaw cycles are smaller, contributing to a more complete hydration reaction. The freeze–thaw damage model established in this study accurately reflects the freeze–thaw damage law of EPS concrete and provides a reference for studying the mechanical properties of EPS concrete under freeze–thaw cycles. The research findings of this study can enhance the strength and service life of EPS concrete, expanding its application scope as a structural material. The study provides valuable insights for future research and engineering applications related to the frost resistance of EPS concrete.