Jessica Sjah

Dr. Jessica Sjah


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 June 2023 in Buildings
Verified
Journal Article
Open access
PDF file
EEEristra Nungsatria Tresna Ernawan
Eristra Nungsatria Tresna Ernawan
JSJessica Sjah
Jessica Sjah
NHNURAZIZ HANDIKA
NURAZIZ HANDIKA
SASotya Astutiningsih
Sotya Astutiningsih
EVEric Vincens
Eric Vincens
This study aimed to analyze the mechanical, displacement, and strain properties of concrete with Ferronickel Slag (FNS) fine aggregate substitute (0%, 50%, and 100%, by mass, later called FNS-0, FNS-50, and FNS-100, respectively) experimentally using the Digital Image Correlation (DIC) method and the Ultrasonic Pulse Velocity (UPV) test. The FNS used in this study is a by-product that came from a Ferronickel smelter in Indonesia coupled with manufactured sand (M-sand) as the fine aggregate control. A D10 × 20 cm3 cylinder and 15 × 15 × 15 cm3 cube specimens were used to analyze the density, compressive strength, and UPV. Additionally, the cube specimens were tested using the DIC method to analyze the displacement and strain properties. The test results show the highest compressive strength was obtained by FNS-50, followed by FNS-100 and FNS-50. The highest pulse velocity was obtained by FNS-100, followed by FNS-50 and FNS-0. The load–displacement response and strain behavior indicate the specimen that had the most load resistance was FNS-50, followed by FNS-100 and FNS-0. Poisson’s ratio obtained using DIC and strain gauges showed consistent results where FNS-0 had the highest values, followed by FNS-50 and FNS-100. Overall, concrete with FNS substitute showed higher density, compressive strength, pulse velocity, and stiffness, as well as lower Poisson’s ratio compared to control concrete (FNS-0).

1 May 2020 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
RIR A Idhar
R A Idhar
JSJessica Sjah
Jessica Sjah
NHN Handika
N Handika
ETE Tjahjono
E Tjahjono
To obtain the material properties of reinforcing steel bar (rebar), a tensile test must be performed in the laboratory. Some standards, such as SNI and ASTM, standardize the condition of the sample and the loading rate of the tensile test. ASTM E8M regulates the loading application (1.15-11.5 MPa/s) of steel rebar test under tension to determine yield properties and SNI 07-2529-1991 governs 10 MPa/s as the maximum loading rate. These circumstances affect the duration of tensile test in real condition, which may lead to one hour of tensile test. In this article, the effect of loading rate of pre-conditioned steel bars (by reducing the section, grinding, and/or lathe according to SNI 07-2529-1991) is investigated using deformed bars (BJTS 40, certified by industries). Random samples of steel reinforcement bar are tested under three different loading rate applications. The result of the material properties of rebar, such as stress-strain curve, yield strength, and ultimate strength, are discussed and analyzed in this study. Different speed tests resulting in different stress rates before yield. However, the stress-strain responses of specimens in the range of linear elastic material are similar. Moreover, at the post-yield/plastic region, the loading rate significantly affected the ductility of the material.

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
EHExa Heydemans
Exa Heydemans
JSJessica Sjah
Jessica Sjah
DMD. R. Marthanty
D. R. Marthanty
EBErly Bahsan
Erly Bahsan
This paper presents numerical simulations using an open boundary algorithm with modified dynamic boundary condition (mDBC) for weakly compressible smoothed particle hydrodynamics models from particle-based code Dualsphysics. The problems of piping erosion in earth dams are aimed at studying the algorithm. The case 2D model of fluid flow past around a fixed cylinder is simulated, where various values of Reynold’s numbers (Re 20 to Re 100) and different viscosity terms are considered. A constant velocity with different values of viscosity for generating various Reynold’s numbers is modeled. The interaction between solid particles of the cylinder and fluid particles is concerned, the cylinder is affected by the hydrodynamics force caused by the flow of fluid particles. The solid particles of the cylinder are the observation points to obtain force and pressure due to the hydrodynamics forces. As a result of the simulation which is to show the capability to model 2D fluid flow with various Reynold’s numbers. Drag coefficient, lift coefficient, and Strouhal number are compared to the previous work from literature.

4 December 2024 in Materials Proceedings
Verified
Conference Paper
Open access
PDF file
MFMuhammad Faisal
Muhammad Faisal
JSJessica Sjah
Jessica Sjah
JRJosia Irwan Rastandi
Josia Irwan Rastandi
This study examines the age-dependent development of compressive strength in Portland pozzolan cement (PPC) concrete under both curing and non-curing conditions. Four beam specimens, each measuring 500 mm × 200 mm × 350 mm, were prepared with varying compressive strengths. Testing was conducted at 28, 60, 90, and 180 days using the rebound hammer test and Windsor Pin Test. The results indicate the tool’s reliability in predicting gradual increases in strength over time. However, this correlation suggests that the factors influencing compressive strength, such as moisture, concrete age, surface smoothness, and environmental exposure, play crucial roles in affecting rebound readings and surface hardness.

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
EBErly Bahsan
Erly Bahsan
KYKevin Yoseph
Kevin Yoseph
JSJessica Sjah
Jessica Sjah
Direct shear is one of the simple tests that can be conducted in the laboratory to obtain the shear strength parameters (i.e., cohesion and friction angle). Bas Direct shear is one of the simple tests that can be conducted in the laboratory to obtain the shear strength parameters (i.e., cohesion and friction angle). Bas

29 November 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
SRS Rachman
S Rachman
JSJessica Sjah
Jessica Sjah
DMDwinanti Rika Marthanty
Dwinanti Rika Marthanty
HSH Soeryantono
H Soeryantono
In Computational Fluid Dynamics, fluid-fluid interaction is used to model the behaviour of two different fluids as a mixture. The numerical simulations of fluid-fluid interaction were carried out by using Smoothed Particle Hydrodynamics (SPH) method based on Navier-Stokes equation in FORTRAN programming language. Correct assumptions and other suitable conditions are needed to reach best fluid-fluid interaction simulation. The term of viscosity force equation was written to model the multiple-fluid interactions. This research uses two different fluids in density and viscosity within a three-dimensional cube container. In order to get a pure interaction of fluids, other effects and influences like chemical reaction and heat transfer are neglected. The fluids are miscible with each other. The fluid particle collisions to container are regarded as perfectly elastic collisions. The simulations of two different fluids in this research showed different particle movements in each numerical simulation, but similar to its actual behaviour.