One of the key reasons for the deterioration of antenna pointing accuracy for radio telescopes is the deformation and tilt of antenna alidades, which primarily result from track unevenness and thermal gradients. A high-precision inclinometer measurement system is installed to investigate the tilt of the antenna alidade and the pointing errors caused thermally. An environment control box with a leveling base was designed to reduce the interference of the external environment, which proved to be effective in guaranteeing the zero-point stability and repeat accuracy of the inclinometer. The tilt of the alidade caused by the track unevenness was measured by a test of slowly rotating the antenna along the azimuth at windless nighttime. A 5-day antenna stationary test and a 48 h astronomical pointing error measurement were performed, which proved the inclinometer measurement system is capable of measuring the thermally induced inclinations with acceptable accuracy. Through a preliminary compensation experiment, the pointing error is compensated from 37″ to 12″, which shows that the application of the system has a good effect on improving the pointing accuracy of the antenna. The system with high measurement accuracy, good system stability, and low computational complexity, proves an effective tool for the radio telescope to solve the problem of real-time measurement and compensation for antenna pointing errors.
Accurate kinematic calibration of subreflector actuators is essential for pointing precision of large radio telescopes, particularly at high frequencies. Conventional least-squares methods are vulnerable to noise and outliers, and their accuracy may degrade when limited pose diversity leads to poor parameter excitation. To address these challenges, this paper proposes a novel robust self-calibration framework that integrates Huber loss and regularization into the Levenberg–Marquardt (LM) algorithm—yielding a hybrid optimization approach that combines residual robustness, numerical stability, and convergence reliability. A comprehensive simulation study was conducted under varying workspace sizes and sensor noise levels. The proposed method maintained stable performance even under reduced excitation and high-noise conditions, where traditional LM methods typically degrade, confirming its robustness and applicability to realistic calibration scenarios. The framework was further validated using a structured-light 6-DOF pose measurement system, the proposed method achieved over 90% improvement in both position and orientation accuracy compared to the traditional LM approach. These findings confirm the method’s effectiveness for high-precision 6-DOF calibration in parallel mechanisms, and its suitability for real-world applications in radio telescope subreflector alignment.
Obtaining an antenna’s back-up structure (BUS) temperature field is an essential prerequisite for analyzing its thermal deformation. Thermodynamic simulation can obtain the structure’s thermal distribution, but it has low computational accuracy. There is a problem with cumbersome wiring and difficult maintenance of the temperature measurement system. This study developed an improved RIME-XGBoost model to realize the temperature prediction of the BUS of the Nanshan 26-m Radio Telescope (NSRT). The proposed model successfully predicts the NSRT’s BUS temperature distribution based solely on environmental sensing (ambient temperature, angle of solar radiation, antenna’s orientation, etc.). The relative prediction accuracy between the predicted and actual BUS temperature is 97.15%, and the predictive error is less than 0.897 K (root mean square error, RMSE). This research result provides an alternative method for the real-time reconstruction of the structure’s thermal distribution in large-aperture radio telescopes.
There are many factors that cause pointing errors in radio telescopes. As one of the motion positioning mechanisms of the radio telescope, the error caused by the elevation mechanism cannot be ignored. The source of error in the elevation mechanism comes mainly from the key transmission components and the support structure. Accurate measurement of the errors caused by them is the key to analyzing their law of change. Aiming at the main error factors in the antenna elevation mechanism, this study builds a scaled-down experimental platform for the elevation mechanism and proposes an error measurement method based on multiencoder information sources. The method compares the error law of change of the antenna elevation mechanism under different driving modes, different centerline deviations of the bearings, and different backlashes and designs error measurement experiments for the abovementioned operating conditions. The results show that the error measurement method based on multiencoder information sources can accurately measure the error of the antenna elevation mechanism under different driving modes. The method can also accurately reflect the law of change in transmission error when the backlash of the elevation mechanism and the centerline deviation of the bearings increase. The final experimental measurement shows that the driving mode of the dual-motor can eliminate about 70% of the mechanism error caused by the backlash. The average value of the error increases by a factor of 1.9 when the backlash increases from 0.1 mm to 1.26 mm. The average value of the error increases by a factor of 5 when the centerline deviation of the bearings increases from 0 to 1.5 mm. This has a good reference value to correct for the pointing error of a radio telescope.