Thi My Huyen Nguyen

Dr. Thi My Huyen Nguyen


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 September 2023 in Materials
Verified
Journal Article
Open access
PDF file
HPHuy Pham
Huy Pham
TNThi My Huyen Nguyen
Thi My Huyen Nguyen
CBChung Wung Bark
Chung Wung Bark
Perovskite solar cells (PSCs) have garnered considerable attention over the past decade owing to their low cost and proven high power conversion efficiency of over 25%. In the planar heterojunction PSC structure, tin oxide was utilized as a substitute material for the TiO2 electron transport layer (ETL) owing to its similar physical properties and high mobility, which is suitable for electron mining. Nevertheless, the defects and morphology significantly changed the performance of SnO2 according to the different deposition techniques, resulting in the poor performance of PSCs. In this review, we provide a comprehensive insight into the factors that specifically influence the ETL in PSC. The properties of the SnO2 materials are briefly introduced. In particular, the general operating principles, as well as the suitability level of doping in SnO2, are elucidated along with the details of the obtained results. Subsequently, the potential for doping is evaluated from the obtained results to achieve better results in PSCs. This review aims to provide a systematic and comprehensive understanding of the effects of different types of doping on the performance of ETL SnO2 and potentially instigate further development of PSCs with an extension to SnO2-based PSCs.

20 November 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
TNThi My Huyen Nguyen
Thi My Huyen Nguyen
MTManh Hoang Tran
Manh Hoang Tran
CBChung Wung Bark
Chung Wung Bark
In this study, a highly crystalline and transparent indium-tin-oxide (ITO) thin film was prepared on a quartz substrate via RF sputtering to fabricate an efficient bottom-to-top illuminated electrode for an ultraviolet C (UVC) photodetector. Accordingly, the 26.6 nm thick ITO thin film, which was deposited using the sputtering method followed by post-annealing treatment, exhibited good transparency to deep-UV spectra (67% at a wavelength of 254 nm), along with high electrical conductivity (11.3 S/cm). Under 254 nm UVC illumination, the lead-halide-perovskite-based photodetector developed on the prepared ITO electrode in a vertical structure exhibited an excellent on/off ratio of 1.05 × 104, a superb responsivity of 250.98 mA/W, and a high specific detectivity of 4.71 × 1012 Jones without external energy consumption. This study indicates that post-annealed ITO ultrathin films can be used as electrodes that satisfy both the electrical conductivity and deep-UV transparency requirements for high-performance bottom-illuminated optoelectronic devices, particularly for use in UVC photodetectors.

1 January 2017 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
TNThi My Huyen Nguyen
Thi My Huyen Nguyen
PTPham Thi Thuy Trang
Pham Thi Thuy Trang
NDNguyen Minh Dat
Nguyen Minh Dat
NHNguyen Huu Hieu
Nguyen Huu Hieu
In this paper, chitosan (CTS) with molecular weight (Mw) ∼810 kDa and degree of deacetylation (DDA) ∼83% was synthesized from prawns shell. Graphene oxide (GO) was prepared by improved Hummers method. CTS/GO nanocomposites were lyophilized using aldehyde formic as a cross-linked to obtain the hydrogels. The hydrogels were freeze dried to make CTS/GO nanocomposite. Characterizations of the CTS/GO nanocomposites were performed by Fourier transform infrared spectroscopy, transmission electron microscopy, X-ray diffraction, and Brunauer-Emmett-Teller specific surface area. Additionally, the effects of pH, contact time, and initial concentration on adsorption for methylene blue (MB) were investigated. The results showed that the CTS/GO nanocomposites were found to be good adsorbent for MB with a maximum adsorption capacity of 662.25 mg/g according to the Langmuir isotherm model. The adsorption data could be well described by pseudo-second-order model. After the adsorption, CTS/GO nanocomposite was easily recovered by filtration or low speed centrifugation. Accordingly, this study demonstrates potential CTS/GO adsorbent for the removal of MB from aqueous solution.

14 May 2023 in Coatings
Verified
Journal Article
Open access
PDF file
TNThi My Huyen Nguyen
Thi My Huyen Nguyen
CBChung Wung Bark
Chung Wung Bark
In this study, an in-situ piezoelectric effect is integrated into a photoactive region to develop a self-powered ultraviolet photodetector based on a p-n junction of ZnO@Polyvinylidene fluoride (PVDF) and poly [9,9-dioctylfluorene-co-N-[4-(3-methylpropyl)]-diphenylamine] (TFB). A ZnO@β-PVDF nanocomposite is fabricated using PVDF with the β-phase as the polymer matrix and ZnO nanoparticles as fillers. The strong piezoelectricity of β-PVDF can facilitate the separation and transport of photogenerated electrons in the depletion area and considerably reduce the dark current when the device is polarized with an external bias, resulting in an improvement in the on/off ratio and detectivity. Under 365-nm UV illumination, the as-fabricated device exhibits a high detectivity of 4.99 × 1011 Jones, an excellent on/off ratio (up to 2.75 × 104), and a fast response speed of 46/53 ms (rise/fall times). The device functions stably over approximately 1000 continuous on/off cycles and exhibits extremely long-lasting photostability when exposed to UV light. The findings demonstrate a promising strategy for enhancing the performance of photodetectors for industrial applications.