A laminate and gradient structured (LGS) AZ31 magnesium alloy was produced via a combination of surface mechanical attrition treatment (SMAT) and accumulative roll-bonding (ARB) in an attempt to improve the AZ31 strength-ductility relationship. The effects of the rolling temperature and number of passes on the microstructure and mechanical properties were researched. The LGS AZ31 Mg alloy microstructure included periodic distributions of fine grain (FG) layers, coarse grain (CG) layers, and FG layers in which the grain size exhibited a gradient transition. A depth-dependent gradient microhardness was generated because of the corresponding gradient microstructure. The effect of the LGS AZ31 Mg alloy on grain size-dependent strengthening mechanisms was researched. The yield and ultimate tensile strengths of the alloy improved dramatically and there was a slight decrease in the fracture elongation. The tensile properties of the sample present good strength-ductility relationships. This is attributed to LGS. The microstructure could change the crack propagation path and enhance alloy strength without much harm to plasticity. The overall influences of SMAT and ARB on mechanical properties, which include dynamic recrystallisation, dislocation activity, and the influences of interfaces, were researched. To illuminate the differences in the deformation behaviours of FG and CG layer microstructures, tensile test samples were imaged via SEM.
10 February 2024 in Journal of Environmental Chemical Engineering
The phase constitutions of as-cast magnesium (Mg)-Zn-Gd alloys (Zn/Gd = 0.25~60, Zn 0~10 at.%, Gd 0~2 at.%, 48 samples) were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The Mg-Zn-Gd phase diagram focused on the Mg-rich corner (with up to 20 at.% Zn, 10 at.% Gd) has been set up. Five regions can be classified as follows: (I) α-Mg+W-phase+(binary compounds), (II) α-Mg+W-phase+I-phase(+binary compounds), (III) α-Mg+I-phase(+binary compounds), (IV) α-Mg+binary compounds, and (V) α-Mg. The phase diagram has been verified by solidification behaviors observation using differential thermal analysis (DTA). Moreover, the structures of I-phase and W-phase in the alloy were explored in details. In terms of the Hume-Rothery rules, I-phase is confirmed as FK-type quasicrystalline with a chemical stoichiometry as Mg30±1Zn62Gd8±1 (at.%). The composition and lattice parameter a W-phase (fcc structure, ) are affected by the composition of Mg-Zn-Gd alloys, especially by the Zn/Gd ratio of alloys. This work would be instructive for the design of Mg-Zn-Gd alloys to obtain the phase components, and then selected the strengthening ways, which could adjust its mechanical properties.
Far-red (FR) emitting LEDs are known as a promising supplement light source for photo-morphogenesis of plants, in which FR emitting phosphors are indispensable components. However, mostly reported FR emitting phosphors are suffering from problems of wavelength mismatch with LED chips or low quantum efficiency, which are still far from practical applications. Here, a new efficient FR emitting double-perovskite phosphor BaLaMgTaO6:Mn4+ (BLMT:Mn4+) has been prepared by sol-gel method. The crystal structure, morphology and photoluminescence properties have been investigated in detail. BLMT:Mn4+ phosphor has two strong and wide excitation bands in the range of 250–600 nm, which matches well with a near-UV or blue chip. Under 365 nm or 460 nm excitation, BLMT:Mn4+ emits an intense FR light ranging from 650 to 780 nm with maximum emission at 704 nm due to 2Eg → 4A2g forbidden transition of Mn4+ ion. The critical quenching concentration of Mn4+ in BLMT is 0.6 mol%, and its corresponding internal quantum efficiency is as high as 61%. Moreover, BLMT:Mn4+ phosphor has good thermal stability, with emission intensity at 423 K keeping 40% of the room temperature value. The LED devices fabricated with BLMT:Mn4+ sample exhibit bright FR emission, which greatly overlaps with the absorption curve of FR absorbing phytochrome, indicating that BLMT:Mn4+ is a promising FR emitting phosphor for plant growth LEDs.