Tamara van Roo

Dr. Tamara van Roo

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 November 2021 in Journal of Reinforced Plastics and Composites
Verified
Journal Article
Open access
PDF file
TRTamara van Roo
Tamara van Roo
Stefan KollingStefan Kolling
Stefan Kolling
FDFelix B Dillenberger
Felix B Dillenberger
JAJoachim Amberg
Joachim Amberg
Injection molding is a common process for manufacturing thermoplastic polymers. Preconnected to fabrication, mechanically loaded parts are examined in structural simulation. A crucial prerequisite for a valid structural simulation for any material is the underlying material data. To determine this data, different phenomena must be considered such as influences of load type, strain rate, environmental conditions and in case of fiber reinforced materials the fiber orientation (FO) in the considered area. Because of rheological effects, injection molded parts often possess a non-homogeneous FO distribution. This makes it challenging to create testing plates for specimen extraction with a well-defined FO over thickness and width in the considered area. In this paper, a novel testing part is introduced with an unidirectionally oriented testable area. It shows a FO degree of more than 0.75, which has been validated with μ-CT measurement and two thermoplastic materials: polyamide and polybutylene terephthalate, both reinforced with 30 weight percent of short glass fibers. In order to resolve influences of the already addressed FO distribution in injection molded parts, tensile test specimens need to be extracted out of specially designed plates via milling and cannot be injection molded directly. Experiments were carried out to study possible effects of preparation on the mechanical properties of specimens with both materials and two milling parameter sets. The first milling parameter set creates reproducible surface roughnesses, whereas the second parameter set shows a correlation between FO and roughness value: when milling perpendicularly to the main FO lower roughnesses are reached than milling in fiber direction. Uncertainties of the normalized rupture strain from orthogonally extracted specimens seem to be larger than the values from those extracted in fiber direction.

2 May 2022 in Materials
Verified
Journal Article
Open access
PDF file
SVSönke Vogel
Sönke Vogel
ABAndreas Brenner
Andreas Brenner
BSBernadette Schlüter
Bernadette Schlüter
BBBernhard Blug
Bernhard Blug
FKFranziska Kirsch
Franziska Kirsch
TRTamara van Roo
Tamara van Roo
Even though hard, low friction coatings such as diamond like carbon (DLC) would be beneficial for the performance and longevity of rubber seals, a crucial challenge remains. The elastic mismatch of rubber substrate and DLC coating prevents a fracture free coating application. In this work, a nature inspired approach is applied to render the stiff coating flexible and resilient to delamination at the same time by direct patterning. Rubber substrates were laser structured with tile patterns and subsequently DLC coated. Tensile and tribology tests were performed on structured and unstructured samples. Unstructured DLC coatings showed a crack pattern induced by the coating process, which was further fragmented by tensile stress. Coatings with tile patterns did not experience a further fragmentation under load. During continuous tribological loading, less heterogenous damage is produced for tile structured samples. The findings are ascribed to the relief of induced coating stress by the tile structure, meaning a more resilient coating.

23 March 2022 in Preprints.org
Verified
Preprint
Open access
PDF file
SVSönke Vogel
Sönke Vogel
ABAndreas Brenner
Andreas Brenner
BSBernadette Schlüter
Bernadette Schlüter
BBBernhard Blug
Bernhard Blug
FKFranziska Kirsch
Franziska Kirsch
TRTamara van Roo
Tamara van Roo
Even though hard, low friction coatings such as diamond like carbon (DLC) would be beneficial for the per-formance and longevity of rubber seals, a crucial challenge – as graphically illustrated in Figure 1.a – remains. The elastic mismatch of rubber substrate and DLC coating prevents a fracture free coating application. In this work a nature inspired approach (Figure 1.b) is applied to render the stiff coating flexible and resilient to delamination at the same time by direct patterning. Rubber substrates were laser structured with tile patterns and subsequently DLC-coated. Tensile and tribology tests were performed on structured and unstructured samples. Unstructured DLC-coatings showed a crack pattern induced by the coating process, which was further fragmented by tensile stress. Coatings with tile patterns did not experience a further fragmentation under load. During continuous tribological loading, less heterogenous damage is produced for tile structured samples. The findings are ascribed to the relief of induced coating stress by the tile structure, meaning a more resilient coating.


Verified
Journal Article
Open access
PDF file
TRTamara van Roo
Tamara van Roo
CMConor Jörg Mager
Conor Jörg Mager
This study aims to assess the mechanical tensile properties of Polyamide produced via selective laser sintering (SLS). The research focuses on the effects of post-processing, positional dependency, anisotropy, and the repeatability of SLS print jobs on material properties. Understanding this anisotropy is crucial for reliable component simulation. A design-appropriate simulation method is developed. A total of 27 identical specimens were fabricated in various orientations and positions within the build chamber, repeated across three print jobs, alongside standard specimens for different post-processing treatments and tempering durations. The mechanical tensile properties were evaluated through tensile tests and compared with simulation outcomes. A new material modeling concept was formulated in the finite element (FE) program ANSYS, employing an orthotropic approach based on linear elastic initial deformation. The Hill Yield Criterion was utilized to model the transition to the plastic region, characterized by a nonlinear strain hardening curve. The print direction was integrated into the FE simulation mesh via a local material coordinate system. Surface treatment via glass bead blasting resulted in slight increases in mechanical response, while tempering had a minor influence. Significant anisotropy was observed, with only the z-position in the build chamber affecting mechanical properties. Successful mapping of anisotropy in structural simulations was achieved. This research did not address optimization of the printing process, recyclate effects, powder aging, or fatigue. The findings provide a comprehensive analysis of the mechanical behavior of SLS-printed specimens, serving as a foundation for treatment methodologies and simulation strategy development.

25 January 2024
Verified
Book Chapter
Closed access
PDF file
TRTamara van Roo
Tamara van Roo