Yi-jen Chiu

Dr. Yi-jen Chiu


Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 June 2020 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
ZSZhenxing Sun
Zhenxing Sun
RXRulei Xiao
Rulei Xiao
ZSZhirui Su
Zhirui Su
KLKui Liu
Kui Liu
ZHZiyang Hu
Ziyang Hu
XCXiangfei Chen
Xiangfei Chen
Multi-wavelength distributed feedback laser array based tunable semiconductor lasers have been widely used owing to their high mode stability and simple tuning scheme. Comparing with the in-parallel laser array, the in-series one can avoid a large power loss caused by the optical combiner. However, the single-mode stability of an in-series laser array is vulnerable to the reflections of other lasers. Here we experimentally demonstrated a tunable in-series laser array with high single-mode stability and high uniformity of wavelength spacing. To reduce the impact of such reflections, the Bragg gratings in different lasers were designed in phase, and the grating phase error was reduced by utilizing the reconstruction-equivalent-chirp technique. Besides, a three-section laser structure was applied in each laser to increase the priority of the dominant lasing mode. Four lasers with small wavelength-spacings of 2.5 nm were integrated in the in-series laser array. According to the measurement results of 40 in-series laser arrays (160 lasers), wavelength deviations of 90.6% lasers were within ±0.2 nm, average wavelength spacings of 97.5% of the measured laser arrays were deviated from the design within ±0.2 nm, and SMSRs of 96.3% lasers were above 45 dB. The output power was above 25 mW and the relative intensity noise was below -130 dB/Hz. Like the in-parallel laser array, the proposed laser array can be applied in either continuous wavelength tuning or fast channel switching. For the continuous wavelength tuning applications, the 10-nm tuning range was obtained with a temperature tuning range of less than 20 °C. For the fast channel switching applications, 4 channels with 2.5-nm spacing are available, and the switching time between two channels was less than 300 ns.

27 June 2008 in IEEE Photonics Technology Letters
Verified
Journal Article
Closed access
TWTsu-Hsiu Wu
Tsu-Hsiu Wu
Yi-jen ChiuYi-jen Chiu
Yi-jen Chiu
FLFang-Zheng Lin
Fang-Zheng Lin
Based on a novel structure of waveguide, a broadband electroabsorption modulator (EAM) with low driving voltage and high extinction ratio has been demonstrated in this letter. The waveguide of InGaAsP-InP p-i-n layer structure is fabricated by two consecutive steps of selective undercut-wet-etching: 1)HCl : H3PO4 on p-InP (p- layer), and 2)H3PO4 : H2O2 : H2O on InGaAsP (active region), showing a wide ridge with a narrow undercut active region. Low capacitance and low cladding impedance can thus be simultaneously attained in such waveguides, leading to low microwave loss and high-speed electrooptical (EO) response. A ridge as wide as 8 mum with a 3-mum- wide active region and a 450-nm gap height in the undercut portion has been fabricated. A 350- mum -long waveguide of EAM is designed, revealing a high extinction ratio of > 30 dB (D.C.) and a modulation efficiency of > 20 dB/V (D.C.) with polarization-insensitive operation at a wavelength of 1550 nm. As high as 60 GHz of a 3-dB bandwidth is measured in the high-speed EO conversion. Calculations by an equivalent circuit model are quite fitted with the measurement, revealing that broadband performance is mainly attributed to the low microwave propagation loss in such waveguides.

7 April 2003 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
YOYae L. Okuno
Yae L. Okuno
JGJon Geske
Jon Geske
KGKian-Giap Gan
Kian-Giap Gan
Yi-jen ChiuYi-jen Chiu
Yi-jen Chiu
Steve DenBaarsSteve DenBaars
Steve DenBaars
John BowersJohn Bowers
John Bowers
We propose and demonstrate a long-wavelength vertical cavity surface emitting laser (VCSEL) which consists of a (311)B InP-based active region and (100) GaAs-based distributed Bragg reflectors (DBRs), with an aim to control the in-plane polarization of output power. Crystal growth on (311)B InP substrates was performed under low-migration conditions to achieve good crystalline quality. The VCSEL was fabricated by wafer bonding, which enables us to combine different materials regardless of their lattice and orientation mismatch without degrading their quality. The VCSEL was polarized with a power extinction ratio of 31 dB.

10 May 2021 in IEEE Journal of Selected Topics in Quantum Electronics
Verified
Journal Article
Closed access
ZSZhenxing Sun
Zhenxing Sun
RXRulei Xiao
Rulei Xiao
ZSZhirui Su
Zhirui Su
KLKui Liu
Kui Liu
GLGen Lv
Gen Lv
XCXiangfei Chen
Xiangfei Chen
We have proposed and experimentally demonstrated a four-channel wavelength-tunable in-series DFB laser array with 100-GHz channel spacing. Compared to the in-parallel laser array, the optical combiner is not utilized and the extra power loss induced by the combiner is avoided. A linearly chirped Bragg grating with multiple phase shifts implemented in the laser cavity is utilized to reduce the grating interference among different lasers. Besides, the reflector sections are inserted at two ends to provide grating feedback for two side channels. With the feedback, all the channels work with low threshold currents. The linearly chirped Bragg grating requires precise control of grating phase variation, which is quite difficult for traditional e-beam-lithography-based method. Here we used the reconstruction-equivalent-chirp technique to fabricate the grating, and precise control of the grating phase is achieved. From the experimental results, the laser arrays work with high output power (>10 mW), relative intensity noise near the relaxation oscillation frequency of below -130 dB/Hz, stable single-mode operation, and high-uniform channel spacing. Fast channel switchings (<600 ns) are obtained by on/off laser switching. Such laser performance enables the proposed laser array to be applied in the dense wavelength division multiplexing technology, especially when fast channel switching is needed, such as the NG-PON2 system.

4 April 2022 in IEEE Photonics Technology Letters
Verified
Journal Article
Closed access
ZSZhenxing Sun
Zhenxing Sun
ZSZhirui Su
Zhirui Su
RXRulei Xiao
Rulei Xiao
YWYaguang Wang
Yaguang Wang
KLKui Liu
Kui Liu
XCXiangfei Chen
Xiangfei Chen
Fast optical switches have the potential of lowering the cost, power, and latency of today’s data-center networks. The on-off switching of DFB lasers in arrays is poised to provide extremely fast switching because the on-off time of a DFB laser is the level of sub-nanosecond. However, the key of the DFB laser array based tunable laser lies in the high precision control of the lasing wavelength. In this letter, we proposed and experimentally demonstrated a tunable laser by integrating 16 DFB lasers based on the reconstruction-equivalent-chirp (REC) technique. Without using the conventional e-beam lithography, an equivalent $\lambda $ /4 phase-shift is fabricated in each DFB laser to ensure the single-longitudinal-mode (SLM) yield. Moreover, high precise wavelength spacing is realized. Wavelength deviations of 89.3% DFB lasers are within ±0.2 nm. The output power of all the channels is above 7 mW, and the relative intensity noise is below −130 dB/Hz. By on-off switching the lasers, sixteen channels with 2.4-nm spacing can be fast switched. The switching time between any two channels is less than 50 ns. In addition, a wide-band continuous wavelength tuning range of 38.4 nm can be obtained with a small temperature variation of 18 °C. Owing to the REC technique, the tunable laser via high-density integration of DFB lasers is demonstrated with simple fabrication, high SLM yield, and high wavelength precision, which opens up a path for wide-band and especially fast tunable lasers.

3 January 2024 in Optics Express
Verified
Journal Article
Closed access
LWLing Wang
Ling Wang
GLGen Lv
Gen Lv
YFYaqiang Fan
Yaqiang Fan
KTKaifei Tang
Kaifei Tang
ZSZhenxing Sun
Zhenxing Sun
YZYating Zhou
Yating Zhou
A distributed feedback (DFB) laser array of twenty wavelengths with highly reflective and anti-reflective (HR-AR) coated facets is both theoretically analyzed and experimentally validated. While the HR facet coating enhances high wall-plug efficiency, it inadvertently introduces a random facet grating phase, thereby compromising the lasing wavelength's predictability and the stability of the single-longitudinal-mode (SLM). In this study, two key advancements are introduced: first, the precisely spaced wavelength is achieved with an error of within ±0.2 nm using the reconstruction-equivalent-chirp (REC) technique; second, the random grating phase on the HR-coated facet is compensated by a controllable distributed phase shift through a two-section laser structure. The SLM stability can be improved while the wavelength can be continuously tuned to the standard wavelength grid. The overall chip size is compact with an area of 4000 × 500 µm2. The proposed laser array has a light power intensity above 13 dBm per wavelength, a high side mode suppression ratio above 50 dB, and low relative intensity noise under -160 dB/Hz. These attributes make it apt for deployment in DWDM-based optical communication systems and as a light source for optical I/O.