Huimin Qi

Prof. Dr. Huimin Qi

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 January 2023 in Lubricants
Verified
Journal Article
Open access
PDF file
FZFan Zhao
Fan Zhao
HHHong Hu
Hong Hu
JYJiaxin Yu
Jiaxin Yu
JLJianping Lai
Jianping Lai
HHHongtu He
Hongtu He
DWDongwei Wang
Dongwei Wang
Ni-B binary coating and Ni-B-W ternary coating were successfully prepared on titanium alloy (TC4) substrates by electroless plating to improve the hardness and wear resistance, followed by annealing treatment for better mechanical properties and tribological properties. The morphology, composition, microstructure, mechanical properties, and tribological behaviors of the coatings were characterized. Both as-plated coatings were amorphous, while the composition and morphology of the Ni-B-W coating differed from those of the Ni-B coating. Additionally, the Ni-B-W coating had better mechanical and tribological properties with a more considerable hardness (13.5 GPa), a minor friction coefficient (0.42), and a lower wear rate (0.10 × 10−7 cm3/(N·m)). After annealing, both coatings were crystalline. In parallel to the as-plated coating, the annealed coatings showed larger hardness values because of the formation of hard phases. Moreover, the crystalline grain of the coatings grew as the annealing temperature rose from 350 °C to 650 °C. Accordingly, the coatings showed a minor hardness value, a major friction coefficient, and severe wear under the same conditions. Above all, the Ni-B-W coating annealed at 350 °C showed the best performance, with an average grain size of 26.3 nm, hardness of 15.9 GPa, friction coefficient of 0.34, and wear rate of 0.09 × 10−7 cm3/(N·m).

19 May 2023 in Polymers
Verified
Journal Article
Open access
PDF file
Huimin QiHuimin Qi
Huimin Qi
YLYang Lei
Yang Lei
XLXuemei Lei
Xuemei Lei
DZDing Zhang
Ding Zhang
Yafeng ZhangYafeng Zhang
Yafeng Zhang
BGBaogang Guo
Baogang Guo
Polyimide-bearing retainer has been successfully used in space environment. However, the structural damage of polyimide induced by space irradiation limits its wide use. In order to further improve the atomic oxygen resistance of polyimide and comprehensively investigate the tribological mechanism of polyimide composites exposed in simulate space environment, 3-amino-polyhedral oligomeric silsesquioxane (NH2-POSS) was incorporated into a polyimide molecular chain and silica (SiO2) nanoparticles were in situ added into polyimide matrix and the combined effect of vacuum environment, and atomic oxygen (AO) on the tribological performance of polyimide was studied using bearing steel as the counterpart by a ball on disk tribometer. XPS analysis demonstrated the formation of protective layer induced by AO. The wear resistance of polyimide after modification was enhanced under AO attack. FIB-TEM confirmed that the inert protective layer of Si was formed on the counterpart during the sliding process. Mechanisms behind this are discussed based on the systematic characterization of worn surfaces of the samples and the tribofilms formed on the counterbody.

2 July 2024 in Coatings
Verified
Journal Article
Open access
PDF file
FZFan Zhao
Fan Zhao
ZZZhou Zhu
Zhou Zhu
JYJiaxin Yu
Jiaxin Yu
ZLZhiquan Luo
Zhiquan Luo
Huimin QiHuimin Qi
Huimin Qi
Working conditions exert an important influence on the tribological properties of protective coatings, thus affecting the wear resistance of workpieces. In this work, a TiAlSiN hardness-modulated multilayer coating with a good match of strength and toughness was deposited on WC-Co substrates. The adhesive wear played a predominant role under the condition of a larger normal load and lower velocity, leading to the formation of a third body layer composed of compressed and lubricating oxides. As a result, the wear rate of the coating tested at 20 N reduced by 23% of that tested at 5 N. Instead, abrasive wear was more manifest, leading to the formation of big-size abrasives, and thus the wear rate increased by 2.8 times while the velocity elevated from 4 mm/s to 16 mm/s. A full factorial analysis of the wear behaviors, including the nanohardness and roughness of the wear track, and the friction coefficient and wear rate of the coating, offered good guidance for the comprehension of the wear form of the TiAlSiN multilayer coating. The results demonstrated the optimization of multilayer structures for TiAlSiN coatings to attain better wear resistance under coupling conditions of normal load and velocity: harder or more lubricated sublayers.

1 October 2024 in Colloids and Surfaces A: Physicochemical and Engineering Aspects
Verified
Journal Article
Closed access
XZXinyi Zhang
Xinyi Zhang
Huimin QiHuimin Qi
Huimin Qi
WLWeiming Lin
Weiming Lin
XGXingshi Gu
Xingshi Gu
RLRuidi Liu
Ruidi Liu
GZGai Zhao
Gai Zhao

19 November 2024 in Langmuir
Verified
Journal Article
Closed access
WLWeiming Lin
Weiming Lin
HSHaonan Song
Haonan Song
Huimin QiHuimin Qi
Huimin Qi
XGXingshi Gu
Xingshi Gu
DZDing Zhang
Ding Zhang
Gai ZhaoGai Zhao
Gai Zhao