Yafeng Zhang

Prof. Yafeng Zhang


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 January 2023 in Lubricants
Verified
Journal Article
Open access
PDF file
FZFan Zhao
Fan Zhao
HHHong Hu
Hong Hu
JYJiaxin Yu
Jiaxin Yu
JLJianping Lai
Jianping Lai
HHHongtu He
Hongtu He
DWDongwei Wang
Dongwei Wang
Ni-B binary coating and Ni-B-W ternary coating were successfully prepared on titanium alloy (TC4) substrates by electroless plating to improve the hardness and wear resistance, followed by annealing treatment for better mechanical properties and tribological properties. The morphology, composition, microstructure, mechanical properties, and tribological behaviors of the coatings were characterized. Both as-plated coatings were amorphous, while the composition and morphology of the Ni-B-W coating differed from those of the Ni-B coating. Additionally, the Ni-B-W coating had better mechanical and tribological properties with a more considerable hardness (13.5 GPa), a minor friction coefficient (0.42), and a lower wear rate (0.10 × 10−7 cm3/(N·m)). After annealing, both coatings were crystalline. In parallel to the as-plated coating, the annealed coatings showed larger hardness values because of the formation of hard phases. Moreover, the crystalline grain of the coatings grew as the annealing temperature rose from 350 °C to 650 °C. Accordingly, the coatings showed a minor hardness value, a major friction coefficient, and severe wear under the same conditions. Above all, the Ni-B-W coating annealed at 350 °C showed the best performance, with an average grain size of 26.3 nm, hardness of 15.9 GPa, friction coefficient of 0.34, and wear rate of 0.09 × 10−7 cm3/(N·m).

1 February 2018 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
Yafeng ZhangYafeng Zhang
Yafeng Zhang
JZJ. Zheng
J. Zheng
JYJ.X. Yu
J.X. Yu
HHH.T. He
H.T. He

19 May 2023 in Polymers
Verified
Journal Article
Open access
PDF file
Huimin QiHuimin Qi
Huimin Qi
YLYang Lei
Yang Lei
XLXuemei Lei
Xuemei Lei
DZDing Zhang
Ding Zhang
Yafeng ZhangYafeng Zhang
Yafeng Zhang
BGBaogang Guo
Baogang Guo
Polyimide-bearing retainer has been successfully used in space environment. However, the structural damage of polyimide induced by space irradiation limits its wide use. In order to further improve the atomic oxygen resistance of polyimide and comprehensively investigate the tribological mechanism of polyimide composites exposed in simulate space environment, 3-amino-polyhedral oligomeric silsesquioxane (NH2-POSS) was incorporated into a polyimide molecular chain and silica (SiO2) nanoparticles were in situ added into polyimide matrix and the combined effect of vacuum environment, and atomic oxygen (AO) on the tribological performance of polyimide was studied using bearing steel as the counterpart by a ball on disk tribometer. XPS analysis demonstrated the formation of protective layer induced by AO. The wear resistance of polyimide after modification was enhanced under AO attack. FIB-TEM confirmed that the inert protective layer of Si was formed on the counterpart during the sliding process. Mechanisms behind this are discussed based on the systematic characterization of worn surfaces of the samples and the tribofilms formed on the counterbody.

1 January 2018 in Journal of Biomechanics
Verified
Journal Article
Closed access
Yafeng ZhangYafeng Zhang
Yafeng Zhang
JZJing Zheng
Jing Zheng
JYJiaxin Yu
Jiaxin Yu
HHHongtu He
Hongtu He

1 December 2016 in Journal of Dentistry
Verified
Journal Article
Closed access
Yafeng ZhangYafeng Zhang
Yafeng Zhang
DLD.Y. Li
D.Y. Li
JYJ.X. Yu
J.X. Yu
HHH.T. He
H.T. He

5 February 2025 in Coatings
Verified
Journal Article
Open access
PDF file
LDLu Ding
Lu Ding
Yafeng ZhangYafeng Zhang
Yafeng Zhang
WLWei Li
Wei Li
YHYue Hu
Yue Hu
SCShaoxiong Cai
Shaoxiong Cai
JYJiaxin Yu
Jiaxin Yu
The electrical contact and tribological performance of contacts are critical for the reliable transmission of electric power and signals. In this study, a nickel layer was applied as an underlayer at the interface, and the effects of its thickness and plating process on the electrical and tribological properties were systematically investigated. Results showed that the coefficient of friction (COF) was reduced due to the nickel layer. The wear loss significantly decreased as the nickel layer thickness increased from 0.5 μm to 2 μm. This is primarily due to the nickel layer reducing adhesive wear. Additionally, the electrical contact resistance (ECR) increased as the top coating was worn out, owing to a reduction in the effective conductive area. Furthermore, ECR, COF, and wear rate were further reduced when the nickel layer was deposited using electroless plating compared with electroplating. In conclusion, the wear resistance of electrical contacts can be improved by a thicker nickel layer or electroless plating. This study provides a theoretical basis for understanding the role of the nickel layer in improving sliding electrical contact and wear behaviors.