The present paper reports the outcomes of activities concerning a real-time SHM system for debonding flaw detection based on ground testing of an aircraft structural component as a basis for condition-based maintenance. In this application, a damage detection method unrelated to structural or load models is investigated. In the reported application, the system is applied for real-time detection of two flaws, kissing bond type, artificially deployed over a full-scale composite spar under the action of external bending loads. The proposed algorithm, local high-edge onset (LHEO), detects damage as an edge onset in both the space and time domains, correlating current strain levels to next strain levels within a sliding inner product proportional to the sensor step and the acquisition time interval, respectively. Real-time implementation can run on a consumer-grade computer. The SHM algorithm was written in Matlab and compiled as a Python module, then called from a multiprocess wrapper code with separate operations for data reception and data elaboration. The proposed SHM system is made of FBG arrays, an interrogator, an in-house SHM code, an original decoding software (SW) for real-time implementation of multiple SHM algorithms and a continuous interface with an external operator.

Structural health monitoring has multifold aims. Concerning composite structures, the main objectives are perhaps reducing costs by shifting from scheduled to on-demand maintenance and reducing weight by removing redundant precautions as the insertion of chicken fasteners to for ensuring joint safety in cases of bonding layer fail. Adhesion defects may be classified along different types, for instance distinguishing between glue deficiency or de-bonding. This paper deals with a preliminary numerical characterization of adhesive layer imperfections on a representative aircraft component. The multipart composite spar is made of two plates and two corresponding C-beams, bonded together to form an almost squared boxed section beam. A numerical test campaign was devoted to extract relevant information from different defect layouts and to try to assess some parameters that could describe their peculiarities. A focus was then given to macroscopic evidence of fault effects behavior, as localization, reciprocal interference, impact on structural response, and so on. A proprietary code was finally used to retrieve the presence and size of the imperfections, correlating numerical outcomes with estimations. Activities were performed along OPTICOMS, a European project funded within the Clean Sky 2 Joint Technology Initiative (JTI).

Morphing aeronautical systems may be used for a number of aims, ranging from improving performance in specific flight conditions, to keeping the optimal efficiency over a certain parameters domain instead of confining it to a single point, extending the flight envelope, and so on. An almost trivial statement is that traditional skeleton architectures cannot be held as a structure modified from being rigid to deformable. That passage is not simple, as a structure that is able to be modified shall be designed and constructed to face those new requirements. What is not marginal, is that the new configurations can lead to some peculiar problems for both the morphing and the standard, supporting, elements. In their own nature, in fact, adaptive systems are designed to contain all the parts within the original geometry, without any “external adjoint”, such as nacelles or others. Stress and strain distribution may vary a lot with respect to usual structures and some particular modifications are required. Sometimes, it happens that the structural behavior does not match with the common experience and some specific adjustment shall be done to overcome the problem. What is reported in this paper is a study concerning the adaptation of the structural architecture, used to host a winglet morphing system, to make it accomplish the original requirements, i.e., allow the deformation values to be under the safety threshold. When facing that problem, an uncommon behavior of the finite element (FE) solver has been met: the safety factors appear to be tremendously dependent on the mesh size, so as to raise serious questions about the actual expected value, relevant for the most severe load conditions. On the other side, such singularities are more and more confined into single points (or single lines), as the mesh refines, so to evidence somehow the numerical effect behind those results. On the other side, standard engineering local methods to reduce the abovementioned strain peaks seem to work very well in re-distributing the stress and strain excesses to the whole system domain. The work does not intend to give an answer to the presented problem, being instead focused on describing its possible causes and its evident effects. Further work is necessary to detect the original source of such inconsistencies, and propose and test operative solutions. That will be the subject of the next steps of the ongoing research.

In recent years, there has been a significant increase in the use of structural health monitoring (SHM) technologies as systems for monitoring the integrity of aircraft’s structures. The use of compact and embeddable sensor networks, like the ones based on fibre optics (FO), is particularly attractive from the perspective of releasing an integrated structural system with intrinsic sensing capacity. Usually, an SHM system architecture is completed by a dedicated algorithm that processes the data gathered from the sensors to elaborate on the level of damage currently suffered by the structure, with the further possibility of providing information to the relevant specialists involved with its supervision. One of the main SHM applications that is attracting major interest is related to the inspection and detection of anomalies in bonded joints, which is extremely relevant in many composite realizations. Aeronautical regulations allow the use of bonded joints on an aircraft’s primary structure but require the implementation of a means to ensure their absolute safety, such as the introduction of further mechanical links aimed at stopping the propagation of a possible flaw or the availability of Non-Destructive Inspection (NDI) systems to prove the absence of relevant damaged areas. Generally, the main typical defects occurring during the manufacturing of bonded joints include adhesive curing, kissing bonds, poor porosity, and poor surface preparation. The current NDI systems more widely used and available to detect defects are still inaccurate due to the lack of standard procedures for the creation of representative defects in a controlled manner, which would allow for the development of reliable methodologies and tools able to ensure the safety of a bonded joint, as required by safety regulations. This paper shows the results relative to the implementation of an SHM system developed by the Italian Aerospace Research Centre (CIRA) aimed at monitoring the bonding lines between spar caps and panels of a typical composite wingbox section and detecting faults in location and length. The work was performed during typical ground static tests by using a fibre optical sensing network embedded within relevant adhesive paste layers during the manufacturing process of the structure. In the reported investigation, the SHM system assumed the function of an NDI system tool. The results show that the developed SHM system has good reliability for the detection of both the position and size of damage areas that were artificially inserted within the test article during the bonding phase, showing its potential as a candidate to be used as a tool to verify the conditions of a bonded joint, as required by aviation authorities’ regulations.

The final objective of the study herein reported is the preliminary evaluation of the capability of an original, real-time SHM system applied to a full-scale wing-box section as a significant aircraft component, during an experimental campaign carried out at the Piaggio Lab in Villanova D’Albenga, Italy. In previous works, the authors have shown that such a system could be applied to composite beams, to reveal damage along the bonding line between a longitudinal stiffening element and the cap. Utilizing a suitable scaling process, such work has then been exported to more complex components, in order to confirm the outcomes that were already achieved, and, possibly, expanding the considerations that should drive the project towards an actual implementation of the proposed architecture. Relevant topics dealt with in this publication concern the application of the structural health monitoring system to different temperature ranges, by taking advantage of a climatic room operating at the Piaggio sites, and the contemporary use of several algorithms for real-time elaborations. Besides the real-time characteristics already introduced and discussed previously, such further steps are essential for applying the proposed architecture on board an aircraft, and to increase reliability aspects by accessing the possibility of comparing different information derived from different sources. The activities herein reported have been carried out within the Italian segment of the RESUME project, a joint co-operation between the Ministry of Defense of Israel and the Ministry of Defense of Italy.

This paper deals with the application of a novel fiber optic SHM system for bonding lines monitoring of a composite aircraft wing within Clean Sky 2 program framework. With the aim of controlling the structural state of the reference component, several targets may be addressed, including safety increase through a periodic update of the integrity level, maintenance costs reduction, for instance, by moving to an on-demand from the usual scheduled approach, and even design benefits by envisaging the possibility of modulating the safety coefficients due to an increased knowledge of the intimate structural system behavior. Specifically, an original SHM architecture is herein presented, based on the use of distributed optical fibers, and implementing a proprietary algorithm, to detect bonding lines damage. Ground testing with a full-scale wing box successfully validated the system’s capability to identify damage. To assess maturity, a TRL evaluation has been carried out, whose results are summarized and discussed. Such a process allowed us to highlight specific areas for technological improvement, such as modeling-testing synergy and operational environment definition. The work herein reported is expected to address these aspects while achieving full-scale aircraft integration, paving the way for enhanced structural robustness and operational safety in future aircraft.