Cutting it close for radical coupling: In principle, electrochemistry is an ideal method for radical coupling: One precursor oxidized at the anode pairs up with a counterpart that has been reduced at the cathode. The trouble is that either or both coupling partners might not stay stable long enough to meet in the middle. Mo et al. resolved this issue by closely spacing the electrodes in a microfluidics platform (see the Perspective by Liu et al. ). They showcase coupling of dicyanobenzene as the cathodic radical precursor with a variety of oxidatively generated partners. Science , this issue p. 1352 ; see also p. 1312
6 August 2020 in Angewandte Chemie International Edition
We present a machine learning-based method for tomographic reconstruction of dense layered objects, with range of projection angles limited to . Whereas previous approaches to phase tomography generally require 2 steps, first to retrieve phase projections from intensity projections and then to perform tomographic reconstruction on the retrieved phase projections, in our work a physics-informed preprocessor followed by a deep neural network (DNN) conduct the 3-dimensional reconstruction directly from the intensity projections. We demonstrate this single-step method experimentally in the visible optical domain on a scaled-up integrated circuit phantom. We show that even under conditions of highly attenuated photon fluxes a DNN trained only on synthetic data can be used to successfully reconstruct physical samples disjoint from the synthetic training set. Thus, the need for producing a large number of physical examples for training is ameliorated. The method is generally applicable to tomography with electromagnetic or other types of radiation at all bands. Significance We demonstrate that it is possible to use deep neural networks to produce tomographic reconstructions of dense layered objects with small illumination angle as low as 10 °. It is also shown that a DNN trained on synthetic data can generalize well to and produce reconstructions from experimental measurements. This work has application in the field of X-ray tomography for the inspection of integrated circuits and other materials studies.
Annealing of cuprous oxide (Cu2O) thin films in vacuum without phase conversion for subsequent inclusion as the channel layer in p-type thin film transistors (TFTs) has been demonstrated. This is based on a systematic study of vacuum annealing effects on the sputtered p-type Cu2O as well as the performance of TFTs on the basis of the crystallographic, optical, and electrical characteristics. It was previously believed that high-temperature annealing of Cu2O thin films would lead to phase conversion. In this work, it was observed that an increase in vacuum annealing temperature leads to an improvement in film crystallinity and a reduction in band tail states based on the X-ray diffraction patterns and a reduction in the Urbach tail, respectively. This gave rise to a considerable increase in the Hall mobility from 0.14 cm2/V·s of an as-deposited film to 28 cm2/V·s. It was also observed that intrinsic carrier density reduces significantly from 1.8 × 1016 to 1.7 × 1013 cm−3 as annealing temperature increases. It was found that the TFT performance enhanced significantly, resulting from the improvement in the film quality of the Cu2O active layer: enhancement in the field-effect mobility and the on/off current ratio, and a reduction in the off-state current. Finally, the bottom-gate staggered p-type TFTs using Cu2O annealed at 700 °C showed a field-effect mobility of ∼0.9 cm2/V·s and an on/off current ratio of ∼3.4 × 102.
18 December 2015 in Measurement Science and Technology
This work presents the design and fabrication of Solidly Mounted Resonator (SMR) devices for the detection of particulate matter (PM2.5 and PM10) in order to develop a smart low-cost particle sensor for air quality. These devices were designed to operate at a resonant frequency of either 870 MHz or 1.5 GHz, employing zinc oxide as the piezoelectric layer and an acoustic mirror made from molybdenum and silicon dioxide layers. Finite element analysis of the acoustic resonators was performed using COMSOL Multiphysics software in order to evaluate the frequency response of the devices and the performance of the acoustic mirror. The zinc oxide based acoustic resonators were fabricated on a silicon substrate using a five mask process. The mass sensitivity of the acoustic resonators was estimated using a 3D finite element model and preliminary testing has been performed. The theoretical and observed mass sensitivity were similar at ca . 145 kHz ng −1 for the 870 MHz resonator when detecting PM2.5 suggesting that SMR devices have potential to be used as part of a miniature smart sensor system for airborne particle detection.
A single-step fabrication method is presented for ultra-thin, linearly variable optical bandpass filters (LVBFs) based on a metal–insulator–metal arrangement using modified evaporation deposition techniques. This alternate process methodology offers reduced complexity and cost in comparison to conventional techniques for fabricating LVBFs. We are able to achieve linear variation of insulator thickness across a sample, by adjusting the geometrical parameters of a typical physical vapor deposition process. We demonstrate LVBFs with spectral selectivity from 400 to 850 nm based on Ag (25 nm) and (75–250 nm). Maximum spectral transmittance is measured at with a -factor of .