Drilling into and around salt bodies could meet different kinds of geohazards, such as shrinkage, stuck, and crushed casing, resulting in well abandonment and huge economic losses. These engineerin...
Salt structures are highly associated with economic hydrocarbon reservoirs. However, drilling a wellbore near or through the salt is usually difficult because the near-salt stresses and pore fluid pressures are largely perturbed due to weaker mechanical strength of salt bodies than their surrounding sediments. We have developed a 2D plane-strain poroelastic finite-element model to simulate stresses and pore pressures in the horizontal-compression salt tectonic system, the Kuqa depression in the Tarim Basin, China, and we use the model results of stresses and pore pressures to calculate safe drilling mud weights on drilling in the salt basin. We found that in early stage of the transient process (close to the undrained condition), pore fluid overpressure occurs at salt convex due to additional compression, whereas underpressure occurs at salt concave due to additional extension within the minibasin. Horizontal effective stress decreases at salt concave (within the minibasin) but increases at salt convex; vertical effective stress varies oppositely to horizontal effective stress. In the final stage of the transient process (drained condition), overpressure has dissipated and pore pressure remains hydrostatic, and stress perturbations are similar to those from the static geomechanical model with elastic sediments: horizontal stress increases at salt convex but decreases at salt concave; vertical stress slightly increases at salt convex and concave. Our calculated safe drilling mud weights and their windows vary over time. Especially at the salt convex, the safe windows are relatively narrow in the early stage of the transient process but become wider in later stage because overpressure dissipates over time and this makes drilling easier. Our results indicate different perturbation patterns of stresses and pore pressures near different salt geometries in a horizontal-compression salt tectonic system, and provide insights into wellbore drilling design and safe drilling mud weights in the salt system.
The pore fluid pressure is important for the generation, migration, and accumulation of hydrocarbons. The Chezhen Sag region in the Bohai Bay Basin is typically characterized by pore fluid overpressure, which is the difference between the pore fluid pressure and the hydrostatic pore pressure. The formation mechanisms of pore overpressure and the accumulation regularity of the “upper source-lower reservoir” type in this region remain unknown. In order to investigate these problems, based on the existing seismic, logging data, and regional tectonic stress environment, we established a two-dimensional finite element model to simulate the fluid–solid coupling processes in the Chegu 25 block of the Chezhen depression. We calculated the abnormal overpressure generated at the source rock during hydrocarbon generation and the processes of hydrocarbon migration and accumulation along the faults and analyzed the dynamic conditions of the hydrocarbon downward accumulation. The results showed that overpressure could accelerate the migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. When the overpressure was too large, tensile fractures and shear fractures could occur, resulting in hydrocarbon dissipation, and changing the results of the oil and gas accumulation. The overpressure at the source rock was mainly caused by hydrocarbon generation, while the overpressure at the reservoir was primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration that exists, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the high permeability of the fault and the existence of pore fluid overpressure can explain the “upper source-lower reservoir” hydrocarbon accumulation model strongly explained the high permeability of faults and the presence of overpressure. The simulated overpressure results were also in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).
Pore fluid pressure is very important to the generation, migration and accumulation of petroleum. The previous studies indicate that the Chezhen sag region is typically characterized by pore fluid overpressure (the difference between pore fluid pressure and hydrostatic pressure). To date, the formation mechanism of pore overpressure and the accumulation regularity of “upper source-lower reservoir” type in this region remains unknown. In order to investigate these problems, a 2-D finite element model is established with regards to the fluid-solid coupling in Chegu 25 block of Chezhen depression, fully considering the existing seismic, logging data and regional tectonic stress environment. Meanwhile, we calculate the abnormal overpressure generated at the source rock during hydrocarbon generation and the process of hydrocarbon migration and accumulation along the faults, analyzing the dynamic conditions of hydrocarbon downward accumulation. The results show that overpressure can accelerate migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. However, when the overpressure is too large, tensile fractures and shear fractures may occur, resulting in hydrocarbon dissipation, and changing the results of oil and gas accumulation. The overpressure at the source rock is mainly caused by hydrocarbon generation, while the overpressure at the reservoir is primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the “upper source-lower reservoir” hydrocarbon accumulation model is strongly explained by the high permeability of faults and the presence overpressure. In summary, the simulated overpressure results are in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).
It has been recognized that stress perturbations in sediments induced by salt bodies can cause elastic-wave velocity (seismic velocity) changes and seismic anisotropy through changing their elastic parameters, thus leading to difficulties in salt imaging. To investigate seismic velocity changes and seismic anisotropy by near-salt stress perturbations and their impacts on salt imaging, taking the Kuqa depression as an example, we have applied a 2D plane-strain static geomechanical finite-element model to simulate stress perturbations and calculate the associated seismic velocity changes and seismic anisotropy; then we used the reverse time migration and imaging method to image the salt structure by excluding and including the stress-induced seismic velocity changes. Our model results indicate that near-salt stresses are largely perturbed due to salt stress relaxation, and the stress perturbations lead to significant changes of the seismic velocities and seismic anisotropy near the salt structure: The maximum seismic velocity changes can reach approximately 20% and the maximum seismic anisotropy can reach approximately 10%. The significant changes of seismic velocities due to stress perturbations largely impact salt imaging: The salt imaging is unclear, distorted, or even failed if we exclude near-salt seismic velocity changes from the preliminary velocity structure, but the salt can be better imaged if the preliminary velocity structure is modified by near-salt seismic velocity changes. We find that the locations where salt imaging tends to fail usually occur where large seismic velocity changes happen, and these locations are clearly related to the geometric characteristics of salt bodies. To accurately image the salt, people need to integrate results of geomechanical models and stress-induced seismic velocity changes into the imaging approach. The results provide petroleum geologists with scientific insights into the link between near-salt stress perturbations and their induced seismic velocity changes and help exploration geophysicists build better seismic velocity models in salt basins and image salt accurately.