The second-order generalized integrator (SOGI) has been widely used to implement grid synchronization for grid-connected inverters, and from grid voltages, it is able to extract the fundamental components with an output of two orthogonal sinusoidal signals. However, if there is a dc offset existing in the grid voltages, the general SOGI's performance suffers from its generated dc effect in the lagging sine signal at the output. Therefore, in this paper, a mixed second- and third-order generalized integrator (MSTOGI) is proposed to eliminate this effect caused by the dc offset of grid voltages. A detailed theoretical analysis on the proposed MSTOGI is presented to reveal the mechanism of eliminating the dc offset. After that, the MSTOGI is applied to a phase-locked loop (PLL) and thereby establish an MSTOGI-PLL which is more adaptable to various grid conditions and power quality. Moreover, a frequency-adaptive control scheme is added to the proposed MSTOGI-PLL to eliminate the phase difference between the PLL output and the grid in grid-connected applications where the grid frequency may vary. Finally, the experimental results from a laboratory prototype are given to demonstrate and verify the effectiveness of the proposed MSTOGI-PLL in terms of steady-state performance, dynamic response, and frequency adaptability.

It is well known that multilevel converters can offer significant benefits in terms of harmonic performance and reduced switching losses compared to their two-level counterparts. However, for lower voltage applications the neutral-point-clamped inverter suffers from relatively large semiconductor conduction losses because the output current always flows through two switching devices. In contrast, the T-type multilevel inverter has less conduction losses because only a single outer loop switching device is required to connect the converter output to the upper and lower dc buses, albeit at the expense of increased switching losses since these outer switches must now block the full dc link voltage. Silicon carbide (SiC) mosfet devices potentially offer substantial advantage in this context with their lower switching losses, but the benefit of replacing all switching devices in a T-type inverter with SiC mosfets is not so clear-cut. This paper now explores this issue by presenting a detailed comparison of the use of Si and SiC devices for a three-level T-type inverter operating in grid-tie applications. The study uses datasheet values, switching loss measurements, and calibrated heat sink thermal measurements to precisely compare semiconductor losses for these two alternatives for a T-type inverter operating at or near unity power factor. The results show that replacing only the dc bus connection switches with SiC devices significantly reduces the semiconductor losses, allowing either the converter power level or the switching frequency to be significantly increased for the same device losses. Hence, the use of SiC mosfets for T-type inverters can be seen to be an attractive and potentially cost-effective alternative, since only two switching devices per phase leg need to be upgraded.

This paper presents the design, modeling, and control of an isolated dc-dc three-port converter (TPC) based on an interleaved-boost full-bridge converter with pulsewidth modulation (PWM) and phase-shift control for hybrid renewable energy systems. In the proposed topology, the switches are driven by phase-shifted PWM signals, where both phase angle and duty cycle are the controlled variables. The power flow between the two inputs is controlled through the duty cycle, whereas the output voltage can be regulated effectively through the phase shift. The primary-side MOSFETs can achieve zero-voltage-switching (ZVS) operation without additional circuitry. Additionally, due to the ac output inductor, the secondary-side diodes can operate under zero-current-switching (ZCS) conditions. In this study, the operation principles of the converter are analyzed and the critical design considerations are discussed. The dynamic behavior of the proposed ac-inductor-based TPC is investigated by performing state-space modeling. Moreover, the derived mathematical models are validated by simulation and measurements. In order to verify the validity of the theoretical analysis, design, and power decoupling control scheme, a prototype is constructed and tested under the various modes, depending on the availability of the renewable energy source and the load consumption. The experimental results show that the two decoupled control variables achieve effective regulation of the power flow among the three ports.

Electrical power systems in future uninterruptible power supplies or electrical vehicles may employ hybrid energy sources, such as fuel cells and supercapacitors. It will be necessary to efficiently draw the energy from these two sources as well as recharge the energy storage elements by the dc bus. In this paper, a bidirectional isolated dc-dc converter controlled by phase-shift angle and duty cycle for the fuel-cell hybrid energy system is analyzed and designed. The proposed topology minimizes the number of switches and their associated gate driver components by using two high-frequency transformers that combine a half-bridge circuit and a full-bridge circuit together on the primary side. The voltage doubler circuit is employed on the secondary side. The current-fed input can limit the input current ripple that is favorable for fuel cells. The parasitic capacitance of the switches is used for zero voltage switching (ZVS). Moreover, a phase-shift and duty-cycle modulation method is utilized to control the bidirectional power flow flexibly and it also makes the converter operate under a quasi-optimal condition over a wide input voltage range. This paper describes the operation principle of the proposed converter, the ZVS conditions, and the quasi-optimal design in depth. The design guidelines and considerations regarding the transformers and other key components are given. Finally, a 1-kW 30~50-V-input 400-V-output laboratory prototype operating at 100-kHz switching frequency is built and tested to verify the effectiveness of the presented converter.

The development of high-frequency power converters is continuously improving their power density, efficiency and fast dynamic response. Among them, high-voltage-conversion-ratio (HVCR) dc–dc converters are widely used in high gain, i.e., step-up/-down or bidirectional applications, such as power supply for data center, dc micro-grids, electrical vehicle charging systems, etc. In this article, the current main high-frequency HVCR dc–dc converters are classified into inductive-based and capacitive-based approaches, which can then be described further by four kinds in detail, namely transformer-based, coupled-inductor-based, and switched-capacitor-based, as well as combination of coupled inductor and switched capacitor. A comprehensive analysis and comparison is given, which can provide guidance for proper topology selection and further topology optimization.