Xueyuan Yang

Dr. Xueyuan Yang

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2023 in Polymer Degradation and Stability
Verified
Journal Article
Closed access
Zongyi DengZongyi Deng
Zongyi Deng
YWYue Wu
Yue Wu
MSMinxian Shi
Minxian Shi
XYXueyuan Yang
Xueyuan Yang
ZHZhixiong Huang
Zhixiong Huang

4 June 2024 in Polymers
Verified
Journal Article
Open access
PDF file
YCYingying Cheng
Yingying Cheng
YJYitong Ji
Yitong Ji
DZDongyang Zhang
Dongyang Zhang
XLXiangda Liu
Xiangda Liu
XZXia Zezhou
Xia Zezhou
WHWenchao Huang
Wenchao Huang
Organic solar cells (OSCs) are one of the most promising photovoltaic technologies due to their affordability and adaptability. However, upscaling is a critical issue that hinders the commercialization of OSCs. A significant challenge is the lack of cost-effective and facile techniques to modulate the morphology of the active layers. The slow solvent evaporation leads to an unfavorable phase separation, thus resulting in a low power conversion efficiency (PCE) of organic solar modules. Here, a nitrogen-blowing assisted method is developed to fabricate a large-area organic solar module (active area = 12 cm2) utilizing high-boiling-point solvents, achieving a PCE of 15.6%. The device fabricated with a high-boiling-point solvent produces a more uniform and smoother large-area film, and the assistance of nitrogen-blowing accelerates solvent evaporation, resulting in an optimized morphology with proper phase separation and finer aggregates. Moreover, the device fabricated by the nitrogen-blowing assisted method exhibits improved exciton dissociation, balanced carrier mobility, and reduced charge recombination. This work proposes a universal and cost-effective technique for the fabrication of high-efficiency organic solar modules.

29 May 2024 in Materials Today Energy
Verified
Journal Article
Closed access
XLXiangda Liu
Xiangda Liu
XLXiujun Liu
Xiujun Liu
ZXZezhou Xia
Zezhou Xia
YJYitong Ji
Yitong Ji
Dongyang ZhangDongyang Zhang
Dongyang Zhang
WHWenchao Huang
Wenchao Huang

20 May 2025 in Polymers
Verified
Journal Article
Open access
PDF file
HWHairun Wen
Hairun Wen
NZNA Zhang
NA Zhang
Zongyi DengZongyi Deng
Zongyi Deng
XYXueyuan Yang
Xueyuan Yang
WHWenchao Huang
Wenchao Huang
Thermal protection materials with excellent performance are critical for hypersonic vehicles. Carbon fiber/phenolic resin composites (Cf/Ph) have been widely used as thermal protection materials due to their high specific strength and ease of processing. However, oxidative failure limits the extensive applications of Cf/Ph in harsh environments. In this paper, a novel hafnium carbide (HfC) and boron carbide (B4C)-modified Cf/Ph was fabricated via an impregnating and compression molding route. The synergistic effect of HfC and B4C on the thermal stability, flexural strength, microstructure, and phase evolution of the ceramizable composite was studied. The resulting ceramizable composites exhibited excellent resistance to oxidative corrosion and ablation behavior. The residual yield at 1400 °C and the flexural strength after heat treatment at 1600 °C for 20 min were 46% and 54.65 MPa, respectively, with an increase of 79.59% in flexural strength compared to that of the composites without ceramizable fillers. The linear ablation rate (LAR) and mass ablation rate (MAR) under a heat flux density of 4.2 MW/m2 for the 20 s were as low as −8.33 × 10−3 mm/s and 3.08 × 10−2 g/s. The ablation mechanism was further revealed. A dense B–C–N–O–Hf ceramic layer was constructed in situ as an efficient thermal protection barrier, significantly reducing the corrosion of the carbon fibers.

6 June 2025 in Materials
Verified
Journal Article
Open access
PDF file
睿胡睿 胡
睿 胡
DXDi Xie
Di Xie
YJYi Jin
Yi Jin
XRXiaojie Ren
Xiaojie Ren
XHXiang Huang
Xiang Huang
WHWenchao Huang
Wenchao Huang
Conventional fabrication of high-efficiency organic solar cells (OSCs) predominantly relies on vacuum-evaporated metal top electrodes such as Ag and Al, which hinder large-scale industrial production. Gallium-based liquid metals (GaLMs), particularly the eutectic gallium–indium alloy (EGaIn), represent promising candidates to conventional vacuum-evaporated metal top electrodes due to their excellent printability and high electrical conductivity. In this study, we fabricated vacuum-free OSCs based on GaLM electrodes (Ga, EGaIn, and Galinstan) and analyzed the device performances. Rigid devices with EGaIn electrodes achieved a champion power conversion efficiency (PCE) of 15.6%. Remarkably, all-solution-processed ultrathin flexible devices employing silver nanowire (AgNW) bottom electrodes in combination with EGaIn top electrodes achieved a PCE of 13.8% while maintaining 83.4% of their initial performance after 100 compression–tension cycles (at 30% strain). This work highlights the potential of GaLMs as cost-effective, scalable, and high-performance top electrodes for next-generation flexible photovoltaic devices, paving the way for their industrial adoption.

8 June 2026 in Polymers
Verified
Journal Article
Open access
PDF file
MMMai Mao
Mai Mao
YHYuwei Hu
Yuwei Hu
LLLidong Liang
Lidong Liang
TCTong Chen
Tong Chen
YJYitong Ji
Yitong Ji
WHWenchao Huang
Wenchao Huang
Sequential deposition (SD) processing offers advantages for morphology optimization of active layer and device stability in organic solar cells (OSCs). However, the insufficient solvent resistance of polymer donor layers often leads to uncontrolled interfacial mixing. Herein, we report a dual-step solvent vapor annealing (D-SVA) strategy to address this limitation, without requiring thermal annealing, making it suitable for ultrathin flexible OSCs. Sequential chlorobenzene (CB) and carbon disulfide (CS2) vapor treatments enhance the molecular ordering and solvent resistance of the underlying donor layer, while reducing residual solvent and improving interfacial properties. As a result, the rigid SD processed OSCs achieve a power conversion efficiency (PCE) of 19.3%. Moreover, ultrathin flexible devices deliver a PCE of 17.3% with good mechanical stability. This work provides a general and scalable pathway toward high-performance and stable SD organic solar cells.