<!-- *** Custom HTML *** --> A significant advancement in the Ce:Nd:YAG solar laser performance using a side-pumping configuration is reported. A solar laser head was composed of a double-stage semispherical lens and a trapezoidal-shaped pumping cavity, which coupled and redistributed the concentrated solar radiation from the focal zone of a parabolic mirror into a laser rod. The laser output performance of a 4.0-mm diameter, 35-mm length Ce:Nd:YAG laser rod was tested and compared with that from a Nd:YAG rod with the same dimensions. At an incoming solar power of 600 W, the Ce:Nd:YAG solar laser achieved 23.6-W / m2 collection efficiency, 4.4% slope efficiency, and 2.8% solar-to-laser power conversion efficiency, which are 1.57, 1.47, and 1.56 times, respectively, higher than the ones obtained with the Nd:YAG rod. The Ce:Nd:YAG side-pumped solar laser has also 1.39 and 1.15 times more collection efficiency and solar-to-laser power conversion efficiency, respectively, than the previous record by Nd:YAG side-pumped solar laser. We demonstrate the great potential of the Ce:Nd:YAG ceramic rod as a gain medium for side-pumped solar lasers.
The Ce:Nd:YAG is a recent active medium in solar-pumped lasers with great potential. This study focuses on the influence of two secondary concentrators: a fused silica aspherical lens and a rectangular fused silica light guide; and consequent pump light distribution on the output performance of a Ce:Nd:YAG side-pumped solar laser. The solar laser head with the aspherical lens concentrated the incident pump light on the central region of the rod, producing the highest continuous-wave 1064 nm solar laser power of 19.6 W from the Ce:Nd:YAG medium. However, the non-uniformity of the absorbed pump profile produced by the aspherical lens led to the rod fracture because of the high thermal load, limiting the maximum laser power. Nevertheless, the solar laser head with the light guide uniformly spread the pump light along the laser rod, minimizing the thermal load issues and producing a maximum laser power of 17.4 W. Despite the slight decrease in laser power, the use of the light guide avoided the laser rod fracture, demonstrating its potential to scale to higher laser power. Therefore, the pumping distribution on the rod may play a fundamental role for Ce:Nd:YAG solar laser systems design.
The solar laser power scaling potential of a side-pumped Ce:Nd:YAG solar laser through a rectangular fused silica light guide was investigated by using a 2 m diameter parabolic concentrator. The laser head was formed by the light guide and a V-shaped pump cavity to efficiently couple and redistribute the concentrated solar radiation from the parabolic mirror to a 4 mm diameter, 35 mm length Ce(0.1 at.%):Nd(1.1 at.%):YAG laser rod. The rectangular light guide ensured a homogeneous distribution of the solar radiation along the laser rod, allowing it to withstand highly concentrated solar energy. With the full collection area of the parabolic mirror, the maximum continuous wave (cw) solar laser power of 40 W was measured. This, to the best of our knowledge, corresponds to the highest cw laser power obtained from a Ce:Nd:YAG medium pumped by solar radiation, representing an enhancement of two times over that of the previous side-pumped Ce:Nd:YAG solar laser and 1.19 times over the highest Cr:Nd:YAG solar laser power with a rectangular light-guide. This research proved that, with an appropriate pumping configuration, the Ce:Nd:YAG medium is very promising for scaling solar laser output power to a higher level.
1 June 2021 in Journal of Solar Energy Engineering
A seven-rod/seven-TEM00 mode beam Fresnel lens solar laser pumping approach is here proposed. The Fresnel lens with 4.0 m2 collection area was used as the primary solar concentrator to pump seven 2.5 mm diameter, 15 mm length Nd:YAG rods within a conical pump cavity through a secondary fused silica aspheric concentrator. Within the pump cavity, solar pump rays not completely absorbed by one of the seven rods were furtherly absorbed by other rods, ensuring hence a high absorption efficiency and avoiding the serious thermal lensing and thermal stress issues associated with classical large rod solar lasers. Seven individual plane-concave large-mode resonators were adopted to enable a good overlap between solar pump mode and TEM00 laser oscillating mode. By using both zemax® and lascad® software, the maximum total TEM00 mode solar laser power of 54.65 W was numerically calculated by optimizing the radius parameter of the Fresnel lens, the diameter of the laser rod, and the radius of curvature of the laser resonator output mirror. TEM00 mode solar laser collection efficiency of 13.66 W/m2 and solar power-to-TEM00 mode laser power conversion efficiency of 1.44% were calculated, representing substantial enhancements of 4.66 times and 4.38 times, respectively, as compared with previous experimental records of the TEM00 mode solar laser pumped through a Fresnel lens with 0.785 m2 collection area. The feasibility of TEM00 mode solar laser power delivery by hollow-core photonic crystal fibers was finally studied.