High density through silicon via (TSV) is a key in fabricating three-dimensional (3-D) large-scale integration (LSI). We have developed polycrystalline silicon (poly-Si) TSV technology and tungsten (W)/poly-Si TSV technology for 3-D integration. In the poly-Si TSV formation, low-pressure chemical vapor deposition poly-Si heavily doped with phosphorus was conformally deposited into the narrow and deep trench formed in a Si substrate after the surface of Si trench was thermally oxidized. In the W/poly-Si TSV formation, tungsten was deposited into the Si trench by atomic layer deposition method after the poly-Si deposition, where poly-Si was used as a liner layer for W deposition. The 3-D microprocessor test chip, 3-D memory test chip, 3-D image sensor chip, and 3-D artificial retina chip were successfully fabricated by using poly-Si TSV.
23 October 2006 in IEEE Transactions on Electron Devices
A three-dimensional (3-D) integration technology has been developed for the fabrication of a new 3-D shared-memory test chip. This 3-D technology is based on the wafer bonding and thinning method. Five key technologies for 3-D integration were developed, namely, the formation of vertical buried interconnections, metal microbump formations, stacked wafer thinning, wafer alignment, and wafer bonding. Deep trenches having a diameter of 2 mum and a depth of approximately 50 mum were formed in the silicon substrate using inductively coupled plasma etching to form vertical buried interconnections. These trenches were oxidized and filled with n+ polycrystalline silicon or tungsten. The 3-D devices and 3-D shared-memory test chips with three-stacked layers were fabricated by bonding the wafers with vertical buried interconnections after thinning. No characteristic degradation was observed in the fabricated 3-D devices. It was confirmed that fundamental memory operation and broadcast operation between the three memory layers could be successfully performed in the fabricated 3-D shared-memory test chip
1 October 1996 in IEEE Transactions on Electron Devices
Metal-Oxide-Semiconductor Field Effect Transistor (MOSFET) has been the major device for integrated circuits over the past two decades. With technology advancement, there have been numerous MOSFET structures for channel length of 0.1 /spl mu/m and below reported in industrial research. A side-by-side comparison of these advanced device structures can provide useful understanding in device physics and the design tradeoffs among MOSFET's parameters. In this work we employ experimental data, device simulation, and analytical modeling for device comparison. The devices were developed at several different research laboratories. Guided by experimental data and simulations, analytical models for topics such as threshold voltage, short-channel effect, and saturation current for these different MOSFET structures are developed. These analytical models are then used for optimizing each device structure and comparing the devices under the same set of constraints for a fair comparison. The key design parameters are highlighted and the strength and weakness of each device structure in various performance categories are discussed.
27 March 2006 in IEEE Transactions on Electron Devices
A capacitorless one-transistor (1T)-dynamic random-access memory (DRAM) cell using gate-induced drain-leakage (GIDL) current for write operation was demonstrated. Compared with the conventional write operation with impact-ionization (II) current, the write operation with GIDL current achieves power consumption that is lower by four orders of magnitude and a write speed within several nanoseconds. The capacitorless 1T DRAM is the most promising technology for high-performance embedded-DRAM large-scale integration.
30 December 2010 in IEEE Transactions on Electron Devices
We have developed a new 3-D hybrid integration technology of complementary metal-oxide-semiconductors, microelectromechanical systems (MEMS), and photonics circuits for optoelectronic heterogeneous integrated systems. We have overcome the fabrication difficulties of optoelectromechanical and microfluidics hybrid integration. In order to verify the applied 3-D hybrid integration technology, we fabricated a 3-D optoelectronic multichip module composed of large-scale integration (LSI), MEMS, and photonics devices. The electrical chips of amplitude-shift keying (ASK) LSI, passive, and pressure-sensing MEMS were mounted onto an electrical Si interposer with through-silicon vias (TSVs) and microfluidic channels. Photonics chips of vertical-cavity surface-emitting lasers and photodiodes were embedded into an optical Si interposer with TSVs. The electrical and optical interposers were precisely bonded together to form a 3-D optoelectronic multichip module. The photonics and electrical devices could communicate via TSVs. The photonics devices could be connected via an optical waveguide formed onto the optical interposer. Microfluidic channels were formed into the interposer by a wafer-direct bonding technique for heat sinking from high-power LSIs. In this paper, we evaluated the basic functions of individual chips of LSI, MEMS, and photonics devices as they were integrated into the 3-D optoelectronic multichip module to verify the applied 3-D hybrid integration technology. LSI, passive, MEMS, and photonics devices were successfully implemented. The 3-D hybrid integration technology is capable of providing a powerful solution for realizing optoelectronic heterogeneous integrated systems.