Takafumi Fukushima

Dr. Takafumi Fukushima

Department of Mechanical Systems Engineering, Graduate School of Engineering, Tohoku University, Sendai 980-8579, Miyagi, Japan

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 December 2010 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
KLKang-Wook Lee
Kang-Wook Lee
ANAkihiro Noriki
Akihiro Noriki
KKKouji Kiyoyama
Kouji Kiyoyama
Takafumi FukushimaTakafumi Fukushima
Takafumi Fukushima
TTTetsu Tanaka
Tetsu Tanaka
MKMitsumasa Koyanagi
Mitsumasa Koyanagi
We have developed a new 3-D hybrid integration technology of complementary metal-oxide-semiconductors, microelectromechanical systems (MEMS), and photonics circuits for optoelectronic heterogeneous integrated systems. We have overcome the fabrication difficulties of optoelectromechanical and microfluidics hybrid integration. In order to verify the applied 3-D hybrid integration technology, we fabricated a 3-D optoelectronic multichip module composed of large-scale integration (LSI), MEMS, and photonics devices. The electrical chips of amplitude-shift keying (ASK) LSI, passive, and pressure-sensing MEMS were mounted onto an electrical Si interposer with through-silicon vias (TSVs) and microfluidic channels. Photonics chips of vertical-cavity surface-emitting lasers and photodiodes were embedded into an optical Si interposer with TSVs. The electrical and optical interposers were precisely bonded together to form a 3-D optoelectronic multichip module. The photonics and electrical devices could communicate via TSVs. The photonics devices could be connected via an optical waveguide formed onto the optical interposer. Microfluidic channels were formed into the interposer by a wafer-direct bonding technique for heat sinking from high-power LSIs. In this paper, we evaluated the basic functions of individual chips of LSI, MEMS, and photonics devices as they were integrated into the 3-D optoelectronic multichip module to verify the applied 3-D hybrid integration technology. LSI, passive, MEMS, and photonics devices were successfully implemented. The 3-D hybrid integration technology is capable of providing a powerful solution for realizing optoelectronic heterogeneous integrated systems.

12 April 2010 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
Takafumi FukushimaTakafumi Fukushima
Takafumi Fukushima
EIE. Iwata
E. Iwata
TKT. Konno
T. Konno
JBJ.-C. Bea
J.-C. Bea
KLK.-W. Lee
K.-W. Lee
MKM. Koyanagi
M. Koyanagi
We have demonstrated fluidic chip self-assembly on Si wafers for fabricating three-dimensional integrated circuits. In this self-assembly technique, small droplets of hydrofluoric acid were employed to simultaneously align many millimeter-scale chips and directly bond them to the hydrophilic bonding areas formed on the host wafers by oxide–oxide bonding. The liquid surface tension enables many Si chips to be self-assembled with the highest alignment accuracy of 50 nm. In addition, many chips were tightly bonded to the hydrophilic bonding areas without applying a mechanical force after the liquid was evaporated at room temperature.

1 May 2017
Verified
Conference Paper
Closed access
ABAdeel A. Bajwa
Adeel A. Bajwa
SJSivaChandra Jangam
SivaChandra Jangam
SPSaptadeep Pal
Saptadeep Pal
NMNiteesh Marathe
Niteesh Marathe
TBTingyu Bai
Tingyu Bai
SISubramanian S. Iyer
Subramanian S. Iyer
The scaling of package and circuit board dimensions is central to heterogeneous system integration. We describe our solderless direct metal-to-metal low pressure (<; 70 MPa) and low temperature (<; 250 °C) thermal compression bonding (TCB) technique and present preliminary results of dielet (4 - 25 mm 2 area) attach to a rigid Silicon Interconnect Fabric (SiIF) with up to two levels of wiring (2 - 10 μm pitch). Dielets were attached at a pitch ≤ 10 μm with an inter-dielet spacing of ≤ 100 μm. We show an effective specific contact resistance of <; 1 Ω-μm 2 and shear strength of > 20 MPa. The combined reduction of dielet interconnect pitch, dielet-to-dielet spacing and trace pitch will enable a Moore's law for packaging.

1 December 2010
Verified
Conference Paper
Closed access
MMM. Murugesan
M. Murugesan
HKH. Kino
H. Kino
HNH. Nohira
H. Nohira
JBJ.C. Bea
J.C. Bea
AHA. Horibe
A. Horibe
MKM. Koyanagi
M. Koyanagi
Mechanical strain/stress and crystal defects are produced in extremely thin wafers (thickness ~10 μm) of 3D-LSIs not only during wafer thinning, but also after wafer bonding using fine-pitch, high-density microbumps and curing. Furthermore, the metal of through-Si via (TSV) and microbump not only becomes the cause of contamination, but also induces strain/stress (due to the difference in the co-efficient of thermal expansion (CTE) between Si and metal) in thinned Si substrate. X-ray photoelectron spectroscopy (XPS) results showed that the crystal quality of Si is highly deteriorated in the ultra-poly ground (UPG) surface after wafer thinning and stress relief. Micro-Raman spectroscopy (μRS) data revealed that a local tensile strain amount to 1.8 GPa was induced by 4×4 μm 2 square sized Si microbumps in 10 μm-thick LSI wafers after bonding and curing. We have noticed that this locally induced strain/stress caused more than 10% change in the ON current of p-MOS transistor. CuSn microbumps have also induced strain/stress at Si wafer surface, and it penetrates deeper for larger bump size and wider for smaller bump pitch.

19 May 2011 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
JBJichel Bea
Jichel Bea
KLKangwook Lee
Kangwook Lee
Takafumi FukushimaTakafumi Fukushima
Takafumi Fukushima
TTTetsu Tanaka
Tetsu Tanaka
MKMitsumasa Koyanagi
Mitsumasa Koyanagi
The influence of Cu contamination from Cu through-silicon via (TSV) on device reliability in the 3-D LSI has been electrically evaluated by capacitance-time (C-t) measurement. The Cu/Ta gate trench capacitors with two types of Ta barrier layers of 10- and 100-nm thicknesses (at the surface) were fabricated. The C-t curves of the trench capacitors with 100-nm-thick Ta layer exhibit no change after annealing up to 60 min at 300 °C. However, the C-t curves of the trench capacitors with 10-nm-thick Ta layer were severely degraded even after the initial annealing for 5 min. It means that Cu atoms diffuse into the active area from the Cu TSV through scallop portions with extremely thin Ta layer in TSVs, and consequently, the generation lifetime of minority carrier is significantly reduced. The C-t analysis is a useful method to electrically characterize the influence of Cu contamination from the Cu TSV on device reliability in fabricated LSI wafers.

11 September 2012 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
Takafumi FukushimaTakafumi Fukushima
Takafumi Fukushima
EIEiji Iwata
Eiji Iwata
YOYuki Ohara
Yuki Ohara
MMMurugesan Mariappan
Murugesan Mariappan
JBJichoel Bea
Jichoel Bea
MKMitsumasa Koyanagi
Mitsumasa Koyanagi
Self-assembly of multichips with metal microbump electrodes is demonstrated by using water surface tension to increase the stacking throughput/yield and chip alignment accuracy of conventional chip-to-wafer 3-D integration. Three-dimensional microbump interconnects are formed by self-assembly with thermal compression at 200°C. Chips with In-Au microbumps with pitches of 10 and 20 μm are tightly bonded to Si wafers after the flip-chip self-assembly process, resulting in high alignment accuracies of 0.8 and 0.2 μm in the x - and y-directions, respectively. Selective hydrophilization by 172-nm excimer lamp irradiation gives a high wettability contrast between hydrophilic chip bonding areas and hydrophobic surrounding areas on the wafers. This assists high-precision multichip self-assembly. A 2500-In-Au-microbump daisy chain is formed with a yield of 100% by flip-chip self-assembly, and it exhibits ohmic contact. The resistance is sufficiently low for 3-D large-scale integration application, being comparable to that obtained by conventional mechanical chip alignment.