Global Ecosystem Dynamics Investigation (GEDI) satellite mission is expanding the spatial bounds and temporal resolution of large-scale mapping applications. Integrating the recent GEDI data into Airborne Laser Scanning (ALS)-derived estimations represents a global opportunity to update and extend forest models based on area based approaches (ABA) considering temporal and spatial dynamics. This study evaluates the effect of combining ALS-based aboveground biomass (AGB) estimates with GEDI-derived models by using temporally coincident datasets. A gradient of forest ecosystems, distributed through 21,766 km² in the province of Badajoz (Spain), with different species and structural complexity, was used to: (i) assess the accuracy of GEDI canopy height in five Mediterranean Ecosystems and (ii) develop GEDI-based AGB models when using ALS-derived AGB estimates at GEDI footprint level. In terms of Pearson’s correlation (r) and rRMSE, the agreement between ALS and GEDI statistics on canopy height was stronger in the denser and homogeneous coniferous forest of P. pinaster and P. pinea than in sparse Quercus-dominated forests. The GEDI-derived AGB models using relative height and vertical canopy metrics yielded a model efficiency (Mef) ranging from 0.31 to 0.46, with a RMSE ranging from 14.13 to 32.16 Mg/ha and rRMSE from 38.17 to 84.74%, at GEDI footprint level by forest type. The impact of forest structure confirmed previous studies achievements, since GEDI data showed higher uncertainty in highly multilayered forests. In general, GEDI-derived models (GEDI-like Level4A) underestimated AGB over lower and higher ALS-derived AGB intervals. The proposed models could also be used to monitor biomass stocks at large-scale by using GEDI footprint level in Mediterranean areas, especially in remote and hard-to-reach areas for forest inventory. The findings from this study serve to provide an initial evaluation of GEDI data for estimating AGB in Mediterranean forest.

Highly accurate, rapid forest inventory techniques are needed to enable forest managers to address the increasing demand for sustainable forestry. In the last two decades, Airborne Laser Scanning (ALS) and Terrestrial Laser Scanning have become internationally established as forest mapping and monitoring methods. However, recent advances in sensors and in image processing – particularly Structure from Motion (SfM) technology – have also enabled the extraction of dense point clouds from images obtained by Digital Aerial Photography (DAP). DAP is cheaper than ALS, especially when the systems are mounted on small unmanned aerial vehicles (UAVs), and the density of the point cloud can easily reach the levels yielded by ALS devices. The main objective of this study was to evaluate and compare the usefulness of ALS-derived and UAV(SfM)-derived high-density point clouds for detecting and measuring individual tree height in Eucalyptus spp. plantations established on complex terrain. A total of 325 reference trees were measured and located in 6 square plots (400 m²). The individual tree crown (ITC) delineation algorithm detected 311 from the ALS-derived data and 259 trees from the UAV(SfM)-derived data, representing accuracy levels of, respectively, 96% and 80%. The results suggest that at plot level, UAV(SfM)-generated point clouds are as good as ALS-derived point clouds for estimating individual tree height. Furthermore, analysis of the differences in digital elevation models at landscape level showed that the elevations of the UAV(SfM)-derived terrain surfaces were slightly higher than the ALS-derived surfaces (mean difference, 1.14 m and standard deviation, 1.93 m). Finally, we discuss how non-optimal UAV-image-acquisition conditions and slope terrain affect the ITC delineation process.

This study aimed to verify the validity of linear, power function and exponential models to estimate stand variables in Galician Atlantic forests of Pinus radiata D. Don using Light Detection and Ranging (LiDAR). These forests differ in structure and species composition from boreal forests, in which this methodology is fully developed. The models tested use LiDAR-derived canopy height and intensity distribution metrics as explanatory variables to predict the following stand attributes: mean height, dominant height, stand basal area, stand volume, stand crown biomass, stand stem biomass and stand aboveground biomass. Exponential models performed best in most cases, with goodness-of-fit statistics similar to those reported in the international literature for boreal forests. The coefficient of determination ranged from 0.44 (for stand crown biomass) to 0.87 (for dominant height), and the root mean square error/mean·100 ranged from 8.2 per cent (for dominant height) to 31.6 per cent (for stand stem biomass). Model precision did not essentially vary after reducing 94 per cent of the original point cloud, i.e. when laser pulse density was reduced from 8 pulses m⁻² to only 0.5 pulses m⁻².

High spatial resolution imagery provided by unmanned aerial vehicles (UAVs) can yield accurate and efficient estimation of tree dimensions and canopy structural variables at the local scale. We flew a low-cost, lightweight UAV over an experimental Pinus pinea L. plantation (290 trees distributed over 16 ha with different fertirrigation treatments) to determine the tree positions and to estimate individual tree height (h), diameter (d), biomass (wa), as well as changes in these variables between 2015 and 2017. We used Structure from Motion (SfM) and 3D point cloud filtering techniques to generate the canopy height model and object-based image analysis to delineate individual tree crowns (ITC). ITC results were validated using accurate field measurements over a subsample of 50 trees. Comparison between SfM-derived and field-measured h yielded an R² value of 0.96. Regressions using SfM-derived variables as explanatory variables described 79% and 86–87% of the variability in d and wa, respectively. The height and biomass growth estimates across the entire study area for the period 2015–2017 were 0.45 m ± 0.12 m and 198.7 ± 93.9 kg, respectively. Significant differences (t-test) in height and biomass were observed at the end of the study period. The findings indicate that the proposed method could be used to derive individual-tree variables and to detect spatio-temporal changes, highlighting the potential role of UAV-derived imagery as a forest management tool.

Wildfires cause substantial environmental and socioeconomic impacts and threaten many Spanish forested landscapes. We describe how LiDAR-derived canopy fuel characteristics and spatial fire simulation can be integrated with stand metrics to derive models describing fire behaviour. We assessed the potential use of very-low-density airborne LiDAR (light detection and ranging) data to estimate canopy fuel characteristics in south-western Spain Mediterranean forests. Forest type-specific equations were used to estimate canopy fuel attributes, namely stand height, canopy base height, fuel load, bulk density and cover. Regressions explained 61–85, 70–85, 38–96 and 75–95% of the variability in field estimated stand height, canopy fuel load, crown bulk density and canopy base height, respectively. The weakest relationships were found for mixed forests, where fuel loading variability was highest. Potential fire behaviour for typical wildfire conditions was predicted with FlamMap using LiDAR-derived canopy fuel characteristics and custom fuel models. Classification tree analysis was used to identify stand structures in relation to crown fire likelihood and fire suppression difficulty levels. The results of the research are useful for integrating multi-objective fire management decisions and effective fire prevention strategies within forest ecosystem management planning.

Crown fire initiation and spread are key elements in gauging fire behaviour potential in conifer forests. Crown fire initiation and spread models implemented in widely used fire behaviour simulation systems such as FARSITE and FlamMap require accurate spatially explicit estimation of canopy fuel complex characteristics. In the present study, we evaluated the potential use of very low-density airborne LiDAR (light detection and ranging) data (0.5 first returns m–2) – which is freely available for most of the Spanish territory – to estimate canopy fuel characteristics in Pinus radiata D. Don stands in north-western Spain. Regression analysis indicated strong relationships (R2 = 0.82–0.98) between LiDAR-derived metrics and field-based fuel estimates for stand height, canopy fuel load, and average and effective canopy base height Average and effective canopy bulk density (R2 = 0.59–0.70) were estimated indirectly from a set of previously modelled forest variables. The LiDAR-based models developed can be used to elaborate geo-referenced raster files to describe fuel characteristics. These files can be generated periodically, whenever new freely available airborne LiDAR data are released by the Spanish National Plan of Aerial Orthophotography, and can be used as inputs in fire behaviour simulation systems.