The requirement to increase inspection speeds for non-destructive testing (NDT) of composite aerospace parts is common to many manufacturers. The prevalence of complex curved surfaces in the industry provides motivation for the use of 6 axis robots in these inspections. The purpose of this paper is to present work undertaken for the development of a KUKA robot manipulator based automated NDT system. A new software solution is presented that enables flexible trajectory planning to be accomplished for the inspection of complex curved surfaces often encountered in engineering production. The techniques and issues associated with conventional manual inspection techniques and automated systems for the inspection of large complex surfaces were reviewed. This approach has directly influenced the development of a MATLAB toolbox targeted to NDT automation, capable of complex path planning, obstacle avoidance, and external synchronization between robots and associated external NDT systems. This paper highlights the advantages of this software over conventional off-line-programming approaches when applied to NDT measurements. An experimental validation of path trajectory generation, on a large and curved composite aerofoil component, is presented. Comparative metrology experiments were undertaken to evaluate the real path accuracy of the toolbox when inspecting a curved 0.5m2 and a 1.6m2 surface using a KUKA KR16 L6-2 robot. The results have shown that the deviation of the distance between the commanded TCPs and the feedback positions were within 2.7mm. The variance of the standoff between the probe and the scanned surfaces was smaller than the variance obtainable via commercial path-planning software. Tool paths were generated directly on the triangular mesh imported from the CAD models of the inspected components without need for an approximating analytical surface. By implementing full external control of the robotic hardware, it has been possible to synchronise the NDT data collection with positions at all points along the path, and our approach allows for the future development of additional functionality that is specific to NDT inspection problems. For the current NDT application, the deviations from CAD design and the requirements for both coarse and fine inspections, dependent on measured NDT data, demand flexibility in path planning beyond what is currently available from existing off-line robot programming software

Environmental and commercial drivers are leading to a circular economy, where systems and components are routinely recycled or remanufactured. Unlike traditional manufacturing, where components typically have a high degree of tolerance, components in the remanufacturing process may have seen decades of wear, resulting in a wider variation of geometries. This makes it difficult to translate existing automation techniques to perform Non-Destructive Testing (NDT) for such components autonomously. The challenge of performing automated inspections, with off-line tool-paths developed from Computer Aided Design (CAD) models, typically arises from the fact that those paths do not have the required level of accuracy. Beside the fact that CAD models are less available for old parts, these parts often differ from their respective virtual models. This paper considers flexible automation by combining part geometry reconstruction with ultrasonic tool-path generation, to perform Ultrasonic NDT. This paper presents an approach to perform custom vision-guided ultrasonic inspection of components, which is achieved through integrating an automated vision system and a purposely developed graphic user interface with a robotic work-cell. The vision system, based on structure from motion, allows creating 3D models of the parts. Also, this work compares four different tool-paths for optimum image capture. The resulting optimum 3D models are used in a virtual twin environment of the robotic inspection cell, to enable the user to select any points of interest for ultrasonic inspection. This removes the need of offline robot path-planning and part orientation for assessing specific locations on a part, which is typically a very time-consuming phase.

Tessellated surfaces generated from point clouds typically show inaccurate and jagged boundaries. This can lead to tolerance errors and problems such as machine judder if the model is used for ongoing manufacturing applications. This paper introduces a novel boundary point detection algorithm and spatial FFT-based filtering approach, which together allow for direct generation of low noise tessellated surfaces from point cloud data, which are not based on pre-defined threshold values. Existing detection techniques are optimized to detect points belonging to sharp edges and creases. The new algorithm is targeted at the detection of boundary points and it is able to do this better than the existing methods. The FFT-based edge reconstruction eliminates the problem of defining a specific polynomial function order for optimum polynomial curve fitting. The algorithms were tested to analyse the results and measure the execution time for point clouds generated from laser scanned measurements on a turbofan engine turbine blade with varying numbers of member points. The reconstructed edges fit the boundary points with an improvement factor of 4.7 over a standard polynomial fitting approach. Furthermore, through adding artificial noise it has been demonstrated that the detection algorithm is very robust for out-of-plane noise lower than 25% of the cloud resolution and it can produce satisfactory results when the noise is lower than 75%. Highlights Introducing novel boundary point detection algorithm and spatial FFT-based filtering approach. Enabling reliable detection of boundary points and smooth boundary reconstruction. FFT-based edge reconstruction works better than polynomial curve fitting. Optimally smoothed edges facilitate the direct use of tessellated models for CAM tasks. The new detection algorithm tolerates out-of-plane noise. The reconstructed edges fit well the detected boundary points.

While both non-destructive evaluation (NDE) and structural health monitoring (SHM) share the objective of damage detection and identification in structures, they are distinct in many respects. This paper will discuss the differences and commonalities and consider ultrasonic/guided-wave inspection as a technology at the interface of the two methodologies. It will discuss how data-based/machine learning analysis provides a powerful approach to ultrasonic NDE/SHM in terms of the available algorithms, and more generally, how different techniques can accommodate the very substantial quantities of data that are provided by modern monitoring campaigns. Several machine learning methods will be illustrated using case studies of composite structure monitoring and will consider the challenges of high-dimensional feature data available from sensing technologies like autonomous robotic ultrasonic inspection. This article is part of the theme issue ‘Advanced electromagnetic non-destructive evaluation and smart monitoring’.