High-precision gas sensors operated at room temperature are attractive for various real-time gas monitoring applications, with advantages including low energy consumption, cost effectiveness and device miniaturization/flexibility. Studies on sensing materials, which play a key role in good gas sensing performance, are currently focused extensively on semiconducting metal oxide nanostructures (SMONs) used in the conventional resistance type gas sensors. This topical review highlights the designs and mechanisms of different SMONs with various patterns (e.g. nanoparticles, nanowires, nanosheets, nanorods, nanotubes, nanofilms, etc.) for gas sensors to detect various hazardous gases at room temperature. The key topics include (1) single phase SMONs including both n-type and p-type ones; (2) noble metal nanoparticle and metal ion modified SMONs; (3) composite oxides of SMONs; (4) composites of SMONs with carbon nanomaterials. Enhancement of the sensing performance of SMONs at room temperature can also be realized using a photo-activation effect such as ultraviolet light. SMON based mechanically flexible and wearable room temperature gas sensors are also discussed. Various mechanisms have been discussed for the enhanced sensing performance, which include redox reactions, heterojunction generation, formation of metal sulfides and the spillover effect. Finally, major challenges and prospects for the SMON based room temperature gas sensors are highlighted.

Hydrogel sensors have received massive attentions for wearable devices, recent advances in the fabrication and network structure of conductive polymer hydrogels are summarized, and their application in the field of wearable sensors is also discussed.

An antenna-coupled split-ring resonator-based microwave sensor is introduced for biosensing applications. The sensor comprises a metallic ring with a slit and integrated monopole antennas on top of a dielectric substrate. The backside of the substrate is attached to a metallic plate. Integrated antennas are used to excite the device and measure its electromagnetic characteristics. The resonant frequency of the device is measured as 2.12 GHz. The characteristics of the device with dielectric loading at different locations across its surface are obtained experimentally. The results indicate that dielectric loading reduces the resonant frequency of the device, which is in good agreement with simulations. The shift in resonant frequency is employed as the sensor output for biomolecular experiments. The device is demonstrated as a resonant biomolecular sensor where the interactions between heparin and fibroblast growth factor 2 are probed. The sensitivity of the device is obtained as 3.7 MHz/(μg/ml) with respect to changes in concentration of heparin.

We present a biosensor based on electromagnetic ring resonator for label-free detection of glucose. The sensing mechanism is based on the principle that the resonant frequencies of such structures depend on the structure geometry and the physical properties of the medium they are in, such as electrical permittivity. The sensor in this paper uses a split-ring resonator fabricated on a flame retardant four substrate via simple printed circuit board fabrication techniques. Glucose oxidase enzyme was incorporated in order to provide biospecificity for glucose. Conductive polymer poly(3,4-ethylenedioxythiophene)poly(styrenesulfonate), also known as PEDOT:PSS, was used for the immobilization of the enzyme on sensor surface. The redshift of the resonant frequency of the sensor in response to DI water, glucose, and NaCl solutions are shown to be in agreement with simulation results and theoretical expectations. In the presence of the enzyme, the sensor loaded with a glucose solution was observed to experience a resonant frequency shift of 17.5 MHz in 15 min, whereas other reagents such as fructose, sucrose, and NaCl did not respond significantly, confirming the biospecificity. The sensor was measured to have a sensitivity of 0.107 MHz/mgml ^-1 ..

The ability to actuate liquids remains a fundamental challenge in smart microsystems, such as those for soft robotics, where devices often need to conform to either natural or three-dimensional solid shapes, in various orientations. Here we propose a hierarchical nanotexturing of piezoelectric films as active microfluidic actuators, exploiting a unique combination of both topographical and chemical properties on flexible surfaces, whilst also introducing design concepts of shear hydrophobicity and tensile hydrophilicity. In doing so, we create nanostructured surfaces that are, at the same time, both slippery (low in-plane pinning) and sticky (high normal-to-plane liquid adhesion). By enabling fluid transportation on such arbitrarily shaped surfaces, we demonstrate efficient fluid motions on inclined, vertical, inverted, or even flexible geometries in three dimensions. Such surfaces can also be deformed and then reformed into their original shapes, thereby paving the way for advanced microfluidic applications.