Bound states in continuum (BICs) are resonances with zero width (infinite lifetime) without any leakage into the surrounding media. Their fascinating properties and potential applications have attracted a great deal of interest. In this paper, we give an analytical, numerical, and experimental demonstration of BICs in simple acoustic structures based on either a single solid layer or a triple solid-liquid-solid layer inserted between two liquids. These modes are an intrinsic property of the inserted structure (solid layer or solid-liquid-solid triple layer) with free surfaces and are independent of the surrounding media. Two kinds of BICs are discussed: (i) Fabry-Perot (FP) BICs exist as the consequence of the intersection of the local resonances induced by inserted structure intersect the transmission zeros induced by the solid layers. (ii) Symmetry-protected (SP) BICs occur when appear at normal incidence due to the decoupling of the transverse modes in the solid layer from the longitudinal modes that propagate in the solid and solid-liquid multilayer media. When the incidence angle departs slightly from the BIC conditions, the latter transform into Fano resonances characterized by an asymmetric line shape in the transmission spectra. In addition, we show that the transmission zeros give rise to negative delay times and therefore acoustic superluminal effect. The theoretical results are obtained by means of the Green’s function method, whereas the experimental measurements are carried out in ultrasonic domain using plexiglass plates in water. These results may have important applications to realize subsonic and acoustic superluminal phenomena as well as acoustic filters and sensors.
We present an efficient and high-sensitive thermal micro-sensor for near wall flow parameters measurements. By combining substrate-free wire structure and mechanical support using silicon oxide micro-bridges, the sensor achieves a high temperature gradient, with wires reaching 1 mm long for only 3 μm wide over a 20 μm deep cavity. Elaborated to reach a compromise solution between conventional hot-films and hot-wire sensors, the sensor presents a high sensitivity to the wall shear stress and to the flow direction. The sensor can be mounted flush to the wall for research studies such as turbulence and near wall shear flow analysis, and for technical applications, such as flow control and separation detection. The fabrication process is CMOS-compatible and allows on-chip integration. The present letter describes the sensor elaboration, design, and micro-fabrication, then the electrical and thermal characterizations, and finally the calibration experiments in a turbulent boundary layer wind tunnel.
This letter describes and discusses the design and testing of an efficient nanogap Pirani micro-sensor for pressure measurements in a wide range with a maximum sensitivity around atmospheric pressure. The structure combines a substrate-free heated wire and a mechanical support made of silicon oxide micro-bridges allowing both a constant nanoscale gap between the wire and the substrate and a 1 mm long and 3 μm wide wire. The high aspect ratio of the wire provides a uniform heating profile along the wire and contributes to low pressure detection. On the contrary, both the nanoscale gap and the short wire length between two micro-bridges contribute to shift the high limit of the pressure range. When tested between 10 kPa and 800 kPa, the sensor presents a wide measurement range, not fully reached by the experiments, with a maximum of sensitivity close to the atmospheric pressure and performances with up to 38%/dec sensitivity when operating in a constant temperature mode with an overheat of 20 °C.
We propose a simple solid–liquid–solid triple layer biosensor platform based on bound states in the continuum (BICs) and Fano resonances to detect the acoustic properties of liquids and apply the method to a mixture of water and albumin with various concentrations. The solid–liquid–solid triple layer is composed of an epoxy as a solid layer and an albumin–water mixture as a liquid layer, and the entire system is immersed in water. In this work, we show that the structure exhibits a high sensitivity (S), quality factor (Q), and figure of merit (FOM) with a better detection limit (DL) in the vicinity of the BICs where the transmission spectra exhibit Fano resonances. The Fano resonances shift towards high frequencies as the concentration increases. The detection limit can reach very small values for a small albumin concentration (). In addition, for a given concentration and layer thickness of the sensing material, we show the effect of the incidence angle on the efficiency of the sensor in terms of the sensitivity and quality factor. The proposed structure can be designed from low-cost material and can be used as a sensor to detect different types of liquids and gases as well.
This paper reports the use of an array of calorimetric micro-sensors that perform bidirectional measurement of wall shear stress, for flow separation detection and control. The sensors design is hot-wire like with three parallel micro wires suspended over a micro-cavity and mechanically supported using periodic perpendicular micro-bridges. The micro-sensors were implemented on a flexible packaging and characterized in a turbulent boundary layer wind tunnel on a flat plate. An array of twelve micro-sensors were then implemented in a flap model designed for active flow control experiments and equipped with pulsed jet actuators. The work included the design and manufacturing of appropriate miniaturized electronics. Without control, the micro-sensors successfully detected the natural flow separation and the flow separation point moving from the trailing edge to the leading edge as the angle of the flap increased. Finally, the micro-sensors characterized the efficiency of the active flow control for avoiding separation.