In this paper, the influence of different fiber materials on the dynamic splitting mechanical properties of concrete was investigated. Brazil disc dynamic splitting tests were conducted on plain concrete, palm fiber-reinforced concrete, and steel fiber-reinforced concrete specimens using a split Hopkinson pressure bar (SHPB) test device with a 100 mm diameter and a V2512 high-speed digital camera. The Digital Image Correlation (DIC) technique was used to analyze the fracture process and crack propagation behavior of different fiber-reinforced concrete specimens and obtain their dynamic tensile properties and energy dissipation. The experimental results indicate that the addition of fibers can enhance the impact toughness of concrete, reduce the occurrence of failure at the loading end of specimens due to stress concentration, delay the time to failure of specimens, and effectively suppress the expansion of cracks. Steel fibers exhibit a better crack-inhibiting effect on concrete compared to palm fibers. The incident energy for the three types of concrete specimens is roughly the same under the same impact pressure. Compared with plain concrete, the energy absorption rate of palm fiber concrete is decreased, while that of steel fiber concrete is increased. Palm fiber-reinforced concrete and steel fiber-reinforced concrete have lower peak strains than plain concrete under the same loading duration. The addition of steel fibers significantly impedes the internal cracking process of concrete specimens, resulting in a relatively slow growth of damage variables.

Re-entrant auxetics offer the potential to address lightweight challenges while exhibiting superior impact resistance, energy absorption capacity, and a synclastic curvature deformation mechanism for a wide range of engineering applications. This paper presents a systematic numerical study on the compressive and flexural behaviour of re-entrant honeycomb and 3D re-entrant lattice using the finite element method implemented with ABAQUS/Explicit, in comparison with that of regular hexagonal honeycomb. The finite element model was validated with experimental data obtained from the literature, followed by a mesh size sensitivity analysis performed to determine the optimal element size. A series of simulations was then conducted to investigate the failure mechanisms and effects of different factors including strain rate, relative density, unit cell number, and material property on the dynamic response of re-entrant auxetics subjected to axial and flexural loading. The simulation results indicate that 3D re-entrant lattice is superior to hexagonal honeycomb and re-entrant honeycomb in energy dissipation, which is insensitive to unit cell number. Replacing re-entrant honeycomb with 3D re-entrant lattice leads to an 884% increase in plastic energy dissipation and a 694% rise in initial peak stress. Under flexural loading, the re-entrant honeycomb shows a small flexural modulus, but maintains the elastic deformation regime over a large range of strain. In all cases, the compressive and flexural dynamic response of re-entrant auxetics exhibits a strong dependence on strain rate, relative density, and material property. This study provides intuitive insight into the compressive and flexural performance of re-entrant auxetics, which can facilitate the optimal design of auxetic composites.

The energy absorption capacity of materials with negative Poisson’s ratio (NPR) is attracting interest from both industry and academia due to the excellent impact resistance of the local shrinkage of materials. However, understanding the compressive behavior of 3D auxetic structures at different strain rates and developing design methods are challenging tasks due to the limited literature and insufficient data. This paper presents a study on the behavior of Poisson’s ratio of an advanced 3D chiral structure, which is formed of two orthogonally positioned 2D hexagonal nodes-based chiral structures. Firstly, both theoretical analysis and numerical simulations are conducted to identify the Poisson’s ratio of 2D chiral structures. The same theoretical value of −1 is obtained for 2D chiral structures with a bending-dominated ligaments assumption. Thereafter, the Poisson’s ratio of 3D chiral structures is determined numerically using a low-speed loaded model composed of 5 × 5 × 8 3D unit cells for eliminating the boundary effects. The results show that impact velocity can strongly affect the energy absorption and deformation behavior of the proposed 3D chiral structure. Increasing the beam radius results in reduced energy absorption capability. However, the energy absorption capability of the 3D chiral structure is not sensitive to the yield strength of nodes. Impact direction affects the energy absorption performance of the 3D chiral structure, depending on the crushing strain. The research results could be used to optimize the design of the proposed novel 3D chiral honeycombs for various applications, such as impact energy absorbers and vibration-resistant dampers.

This study conducted ice-induced vibration analysis on offshore platform structures using the cohesive element method (CEM). The efficacy of this method in simulating the interaction between sea ice and the platform structure is verified by comparing it with the Hamburg Ship Modeling Pool (HSVA) ice-breaking experiment. Subsequently, the vibration response of a sea-ice-jacket platform model is investigated under both unprotected conditions and with the presence of ice-breaking cones. The findings reveal that the motion response of offshore platforms exhibits a positive correlation with the impact velocity of the ice, while the sensitivity of this impact is found to be minimal. Furthermore, the influence of different ice directions on the vibration response of offshore platforms is significant, and the shielding effect has an important impact on the platform’s response. Notably, offshore platforms equipped with 52.5-degree cones demonstrate the most effective vibration reduction, reducing the maximum acceleration by 63% compared to unprotected configurations. It is worth mentioning that as the cone angle increases, the corresponding ice-breaking cone undergoes higher load-bearing.