This study presents a comprehensive examination of Pinus kesiya var. langbianensis (Pinus kesiya var. langbianensis), the primary resin-extraction tree species in Yunnan Province, China. In this study, we formulated different concentration gradients of 0.25%, 0.5%, 1%, and 2% of diquat solution as tapping stimulant to test the effect of different concentrations on the resin gain rate of Pinus kesiya, and analyzed the relationship between anatomical structure, major chemical composition of turpentine and resin yield by methods such as wood anatomy and chemical composition analysis of turpentine. The primary focus of the investigation was on exploring the interrelationships among resin-tapping stimulants, anatomical structures, turpentine components, and resin yield. Research findings demonstrate a significant enhancement in resin production due to the application of stimulants, with the highest increase rate reaching 55% in a specific group, while others achieved approximately 30% increments. Moreover, measurement data about resin duct dimensions indicate a noteworthy increase in resin duct area for the stimulant-treated group compared to the control group. However, it should be noted that the impact on resin duct area by varying stimulant concentrations was relatively minor. Furthermore, continuous observation of resin extraction from different resin-yield classes of P. kesiya revealed insignificant variation in resin yield over time for the low and moderate resin-yield groups. In contrast, the high resin-yield group exhibited a gradual increase in resin production. Interestingly, the high resin-yield group exhibited the smallest resin duct area, but the highest resin duct density, indicating an interconnectedness of resin duct-related data that influences resin yield. Additionally, correlative investigations between anatomical structures and resin yield demonstrate a positive correlation between resin duct area and resin yield, total resin production, and average resin yield. This underscores the importance of resin duct area as a significant factor in resin production. On the other hand, the influence of stimulant concentrations on the turpentine components was found to be negligible. Overall, the correlation results suggest that turpentine components cannot reliably predict or differentiate between high and low resin-yield trees. This study provides a comprehensive analysis of the interrelationships among stimulants, anatomical structures, and turpentine components, offering a theoretical foundation for the resin extraction and resin processing industries in Yunnan Province.

This study takes the wooden components of the different parts of the ancient buildings at the site of the Zhuangzishang Conference as the object of study, and investigates the deterioration state of the different wood components. To assess their degree of degradation, the wood anatomy, basic density (BD), maximum water content (MWC), cell wall major components, X-ray diffraction (XRD), infrared spectroscopy (IR), and thermogravimetry (TG) were used to compare the samples of new and old wood from the same species. The window (W) was identified by microscopic characterization as cypress (Cupressus sp.), the footing beam (FB) and the weatherboard (WB) as pine (Pinus spp.), the purlin (P) and the column (C) as Chinses fir (Cunninghamia spp.), and the floor (F) as spruce (Picea sp.). In terms of their physical properties, the old wood had a lower basic density of 2.58%–38.19%, a lower air-dry density of 2.87%–39.81%, and a higher maximum moisture content of 8.52%–41.38% compared to the reference wood. The degradation of the FB, which has been subjected to moisture and sunlight, and the P, which has been subjected to termite damage, was greater than that of their conspecifics. The integrated holocellulose of the ancient wood was 3.34%–16.48% less, and the hemicellulose was 1.6%–21.92% less compared to that of the reference wood, and the lignin was 1.32%–25.07% more. The XRD results showed that the crystallinity of the cellulose was greater in the different species of ancient wood compared to the control wood, which was caused by the decrease in the amorphous zones of the hemicellulose and cellulose in the ancient wood. The IR indicated that the degradation of cellulose and hemicellulose occurred in the old wood of all species, from the new lignin uptake peaks in the UV-exposed W, FB, and WB compared to the control timber. The pyrolytic behavior of the ancient and control timber is mainly related to the degradation of the tree species and the ancient wood holocellulose. These results show that the differences in the wooden components of the different parts of the ancient buildings at the Zhuangzishang Conference site are mainly related to the species of trees used in the components, and are secondly related to the location of the ancient wood members, which provides useful information for the protection and repair of the ancient buildings at the site.

Rubber wood often exhibits dimensional instability during use, which seriously hinders its widespread application. In order to enhance the dimensional stability of rubber wood, a two-step method was employed in this study to modify rubber wood using two plant-derived compounds, namely sucrose and tung oil. Samples treated alone with sucrose or tung oil were also prepared. The water absorption, dimensional stability, and thermal stability of modified and untreated wood were evaluated. The results show that wood samples treated with 30% sucrose and tung oil had excellent water resistance and dimensional stability based on the synergistic effect of sucrose and tung oil. After 384 h of immersion, the 30% sucrose and tung oil group presented a reduction in water absorption by 76.7% compared to the control group, and the anti-swelling efficiency was 57.85%, which was 66.81% higher than that of the tung oil treatment alone. Additionally, the leaching rate of the 30% sucrose and tung oil group decreased by 81.27% compared to the sample modified with the 30% sucrose solution alone. Simultaneously, the 30% sucrose and tung oil group showed better thermal stability. Therefore, this study demonstrates that the synergistic treatment of modified rubber wood by sucrose and tung oil is an eco-friendly, economical, and highly efficient approach with the potential to expand the range of applications of rubber wood products.

Utilizing conventional wood preservatives poses potential risks to ecosystems and human health. Therefore, the wood protection industry must develop alternatives that are both efficient and environmentally friendly. In this paper, industrial tobacco waste extracts were used as eco-friendly wood preservatives against wood decay fungi. Three major constituents in the extracts were identified via gas chromatography-mass spectrometry (GC-MS) and included nicotine, neophytadiene, and 2,7,11-cembratriene-4,6-diol. The antifungal activities of waste tobacco extracts and these three major constituents against wood decay fungi were tested. At a concentration of 40 mg/mL, the tobacco waste extract treated with 50% ethanol significantly inhibited the activity of wood decay fungi. This was because the extract contained nicotine as the primary active component and neophytadiene as a synergistic active component. Wood decay resistance tests were conducted on Pinus yunnanensis and Hevea brasiliensis treated with a 50% ethanol extract of tobacco waste at a concentration of 40 mg/mL. The mass losses of Pinus yunnanensis exposed to G. trabeum and T. versicolor were 4.11% and 5.03%, respectively, while the mass losses in Hevea brasiliensis exposed to G. trabeum and T. versicolor were 7.85% and 9.85%, respectively, which were classified as highly resistant. The acute ecotoxicity of the tobacco waste extract was assessed using a kinetic luminescent bacteria test with Aliivibrio fischeri, which revealed significantly lower acute toxicity than a commercial copper-based wood preservative. This study offers insights into high-value utilization of tobacco waste and advancement of natural wood preservatives.