Additive manufacturing (AM) offers new possibilities in soft robotics as materials can easily be combined in multi-material designs. Proper sensing is essential for the soft actuators to interact with the surroundings successfully. By fabricating sensors through AM, sensors can be embedded directly into the components during manufacturing. This paper investigates NinjaTek Eels electrical resistance response to strain and the feasibility of using the material to create strain sensors. Strain sensors were 3D-printed out of NinjaTek Eel, a soft conductive TPU, and was tested during cyclic loading. A custom resistance–strain test rig was developed for measuring sensor behavior. The rig was calibrated for electric resistance, able to measure electric resistance as a function of strain. A parabolic response curve was observed during cyclic loading, which led to ambiguous readings. A 10-specimen validation test was conducted, evaluating the statistical variation for the first 100 loading cycles. The validation test showed that the sensor is capable of accurate and predictable readings during single load cases and cyclic loading, with the overall root mean square error being 66.9 Ω. Combining two sensors of different cross-sections gave promising results in terms of calibrating. By monitoring load cycles and strain rates, calibration can also be achieved by machine learning models by the microcontroller used to extract data. The presented work in this article explores the potential of using conductive TPUs as sensors embedded in products such as soft robotics, life monitoring of products with structural, and digital twins for live product to user feedback.
In Additive Manufacturing (AM), new generations of polymer composites presented as engineering- grade materials provide high-end mechanical properties with the design freedom AM provides. Interlayer anisotropy is the main challenge in both in-situ optimization and post-analysis in transitioning from prototypes to high-performance components in fused filament fabrication (FFF). Recent studies show a direct correlation between layer fusion temperature and mechanical properties. In this paper, we present synchronized position and temperature data and study how a component changes based on layer height and geometry. An IR sensor transfers data while printing a G-code generated by FullControllGcode, printing in a single direction and recording temperature in front of the nozzle. Results show that within each layer, a Δt of 20°C at thinner geometries, the heat loss will provide a reduction in mechanical properties and further heat loss occurs when moving away from the heated bed. By using the presented temperature mesh in further studies, post- printed anisotropic components can be analyzed by FEM, and the FFF process can be adaptively optimized based on location, size and geometry.
Composite filaments are getting increased attention in additive manufacturing (AM). More and better solutions for filament production are needed to assist researchers in discovering new materials capable of producing AM-made high-performance parts. This article presents a method for producing composite filament, including an open-source, low-cost automatic composite feeder designed to increase the accuracy and quality of the filament. The feeder includes a fibre screw designed through an iterative prototyping process to accurately control the filament's fibre percentage while reducing lumps' occurrence in a single step. An experiment evaluating the quality of filament made of Polylactic Acid (PLA) and carbon fibre (CF) tested the use of the feeder compared to manual mixing. Filament with a nominal diameter of 2.85mm with 4.5%, 7.9%, 11.2% and 14.5% CF was made. The results suggest that the composite feeder improved the filament quality. The filament diameter RMSE value was reduced from 0.08 to 0.06 and 0.15 to 0.13 for both 4.5% and 11.2%, respectively. The article concludes that the feeder design may help researchers develop and discover new materials while improving the quality of the filament.
1 August 2024 in Frontiers in Mechanical Engineering
Creating specialized components featuring complex structures typically involves extensive time, CAD modelling and manual labor. However, with the right combination of tools and knowledge, complex components can be generated, manufactured, and utilized within hours, rather than weeks or months. By creating a portable manufacturing setup, the designer can produce components on site, significantly enhancing accessibility. An example where time and accessibility are of vital importance is in paralympic cross country skiing where training schedules are tight and snow conditions vary. The aim of this study was to generate and manufacture form-fitted, lightweight knee-supports for a Paralympic sit-ski athlete within 4 days. This was done by 3D printing components generated using Fusion 360s Generative Design (GD), based on inputs from the athlete’s geometry, material testing and force data resulting from the athlete’s weight and movement. A precise fit around the knees was achieved using a high-accuracy 3D scanner and modelling software to create an adjustable prototype to determine knee positions and key angles. Force data from the knees were gathered using a digital twin sit-ski. Based on the collected data, the maximum forces inserted into the GD model were 700N and 500N for the right and left knee, respectively. Material data was obtained through testing ABS samples manufactured under the same conditions as the knee-supports themselves. The Young’s modulus was calculated to and and UTS was and . The GD model generated seven models to choose from for each knee. The supports were manufactured using a 3D printer modified to increase the volumetric flow, effectively reducing manufacturing time. Manufacturing time of the final knee-supports were 6 h 33 min and 7 h 24 min and the total weight of the components including support structures were 468 g and 532 g for the right and left knee, respectively. Later optimized print settings reduced the manufacturing time to 4 h 40 min. In total, two iterations of knee-supports were produced, and the final lightweight versions were mounted onto the sit-ski within 4 days. Qualitative feedback from the athlete revealed improved fit, increased stability, surprisingly short manufacturing time and a generally pleasing result.